Posts by C6ZZKGT

    Here is an Ebay auction for a pair of NOS C5ZZ 15511 A and NOS C5ZZ 15512 A backup light bodies by Ebay member "jollyroge" with a starting bid of $0.99:

    NOS Ford 65-66 Mustang Shelby GT350 back up light assemblies C5ZZ-15512-A C5ZZ-15511-A with gaskets. Here is a pair of NOS back up light assemblies for an early Mustang. This is a matched set of left and right units one in the Ford box with part numbers C5ZZ-15512-A LH and C5ZZ-15511-A RH . They are in perfect shape ready to install on your early Mustang. They come with a pair of NOS matching gaskets C7ZZ-15533-A and one NOZ lens C5ZZ-15514-A . Long obsolete from Ford . Perfect for your period correct show car. Winner pays actual UPS shipping cost. Good luck bidding!

    NOS Ford 65-66 Mustang Shelby GT350 back up light assemblies C5ZZ-15512-A 11-A | eBay

    -Fred-

    Here is an Ebay auction for a used C3OZ 6250 C Hipo camshaft by Ebay member "jollyroge" with a starting bid of $0.99:

    Ford 289 Hi-Po K code Shelby GT350 Mustang camshaft C3OZ-6250-C. Here is an original used 289 Hi-Po solid lifter camshaft that was removed from a 65 Shelby GT350.The Ford part number for this cam is C3OZ-6250-C. It has the upside down AE marking on the cam to designate that it is a factory Ford 289 Hi-Po cam. This is a solid lifter or mechanical camshaft with a valve lash of. 019 , .460 lift and 310degree of advertised duration. This cam would be proper is any 289 Hi-Po powered car from 1963-1967 including Shelby , Cobra , Mustang ,Falcon, Comet, and Fairlane . There has been much cam failure in the last few years because of poor quality control with new cams. This is an original 1960’s cam when they were made well. This cam has been obsolete from Ford for many years and would be an excellent cam for your classic 1960’s small block Ford. This cam will work in 260-289-an 302 engines. Winner pays actual UPS shipping cost. Good luck bidding!

    Ford 289 Hi-Po K code Shelby GT350 Mustang camshaft C3OZ-6250-C | eBay

    -Fred-

    This used C3OZ 6250 C Hipo camshaft sold November 22, 2022 on Ebay for $266.14 with 17 bids from 9 bidders.

    -Fred-

    Here is an Ebay auction for a used C3OZ 6250 C Hipo camshaft by Ebay member "jollyroge" with a starting bid of $0.99:

    Ford 289 Hi-Po K code Shelby GT350 Mustang camshaft C3OZ-6250-C. Here is an original used 289 Hi-Po solid lifter camshaft that was removed from a 65 Shelby GT350.The Ford part number for this cam is C3OZ-6250-C. It has the upside down AE marking on the cam to designate that it is a factory Ford 289 Hi-Po cam. This is a solid lifter or mechanical camshaft with a valve lash of. 019 , .460 lift and 310degree of advertised duration. This cam would be proper is any 289 Hi-Po powered car from 1963-1967 including Shelby , Cobra , Mustang ,Falcon, Comet, and Fairlane . There has been much cam failure in the last few years because of poor quality control with new cams. This is an original 1960’s cam when they were made well. This cam has been obsolete from Ford for many years and would be an excellent cam for your classic 1960’s small block Ford. This cam will work in 260-289-an 302 engines. Winner pays actual UPS shipping cost. Good luck bidding!

    Ford 289 Hi-Po K code Shelby GT350 Mustang camshaft C3OZ-6250-C | eBay

    -Fred-

    In light of this new information, it would be wise to have a prepurchase inspection done on this Kar prior to any negotiations. The description by the previous owner indicates to me that it has had extensive rust repairs plus the color and interior changes.

    -Fred-

    Here is a posting on the old Hipo forum from a previous ownner regarding this Kar:

    I've got a late 65 K, GT, Fastback (5F09K723313) which is silver blue with blue and white deluxe interior. Block is a replacement, however trans back is original. Body has had extensive restoration which as the previous post says, is the norm for a car of this age. I've got over 40K in it plus a lot of time. I haven't had much time for it in the last 2 years and would consider selling it. I have not made any effort to sell it until today. I have the documented ownership records on it back to 1966. There are a few minor things that I just haven't had time to do on it, but basically, it's a pretty sweet car. I would have to get mid 40's for it. It is equiped exactly as it left the factory other than changed color from ivy green to silver blue and interior from parchment/gold to blue & white. Car was on display in Nashville at the 40th anniversary show.

    Scott Steel

    Springville, TN

    65 Mustang Fastback Silver Blue Metallic with blue and white pony interior is for sale by Ebay seller "classic-car-studio" with a Buy-It-Now of $75,900.00 or make offer:

    E-mail: [email protected]
    Phone: 314.567.4200

    This 1965 K Code Mustang Fastback is finished in stunning Silver Blue Metallic over a blue and white Deluxe Pony interior. Features on the car include the correct 289 V8 Hi Po engine, original 4-speed close ratio manual transmission(HEH-T), 3.50:1 9” housing, 14” chrome wheels wrapped in Michelin tires, folding rear seat, remote drivers mirror, 2-speed wipers/washers, Day/Night mirror, interior coat hooks, AM radio, GT equipment package(front disc brakes, larger sway bar, quick ratio steering, trumpeted exhaust, 5 dial dash, GT gas cap, rocker panel stripe, and fog lamps in the grill). The Deluxe interior has special seat upholstery, door panels with armrests, pistol grip door handles, wood grain dash, steering wheel, and the optional center console.

    The engine was professionally rebuilt and has the correct Hi-Po casting number (C5AE-6015E) with the 6-bolt bell housing. The engine is now .03 over and retains the original harmonic balancer, original solid lifter cam, original aluminum 4 blade cooling fan, competition style Hi-Po exhaust manifolds, dual point/centrifugal style advanced distributor, and the correct Autolite 4100 cab that was professionally restored by Pony Carburetors. Compression is the correct 10.5:1 and if she’s warmed up and you’re feeling lucky, you can rip the engine up to the 6,500 RPM redline. The transmission, Z bar clutch arm and 9” rear end remain date coded to this Hi-Po Mustang. The car also uses the mandatory 10.4” K code clutch.

    The suspension and brakes were totally sorted during the restoration. Both the K code and the GT came with the Special Handling package with upgraded springs, shocks, plus a larger 13/16-inch front sway bar. Also included is the quick ratio manual steering box.

    This K code GT is an impressive and thrilling car to drive. These cars were just over 2,600 lbs which is feather light compared to most modern vehicles. Packaged with the upgraded brakes, high HP 289CI and a handling package, these were great sports cars in their day and are still a wonderful analogue drive to this day.

    VIN: 5F09K723313
    Year: 1965
    Make: Ford
    Model: Mustang
    Engine: 289 ci V8
    Transmission: 4-Speed Manual
    Color: Blue over Blue
    Odometer Reading: 92,054

    This special automobile is currently available for sale in our showroom and is also being advertised in other formats. Classic Car Studio reserves the right to end this auction at any time, and as a result, this automobile may not be available for the duration of the eBay listing.

    Prospective bidders are requested to review our “terms” available in our toolbar-as well as, to utilize any of the other features which we have collected there for buyer assistance.

    All images of the vehicle presented for sale are of the actual automobile being sold.

    Buyers are always encouraged to call us directly to answer questions or to assist with purchase arrangements at: 314-567-4200

    Please see our other auctions in our ebaY Motors Store

    1965 Ford Mustang | eBay

    -Fred-


    This used C3AE bare block sold November 23, 2022 on Ebay for $1,275.00 with 22 bids from 10 bidders.

    -Fred-

    Here is an Ebay auction for a used C3AE bare block by Ebay member "jollyroge" with a starting bid of $0.99:

    Original 289 Hi Po engine block 5 bolt 289 Cobra Fairlane C3AE-6015-N . Here is an original 5 bolt 289 Hi Po block. This block is standard bore with matching main caps. It has a part number of C3AE-6015-N with a casting date of 3C14( March 14th 1963). The machine or assembly date is 3D05 April 5th 1963. This block has had a repair to the back water jacket area . This is common place for these blocks to crack if they get cold. It has been professionally welded and it is good to run. We have built many engines including for racing with the same repair and is not something that can be seen once the bellhousing is on. Otherwise an unmolested early 289 Hi Po block that has light surface rust on it because it has been sitting for decades but no heavy rust that would prevent a nice clean over bore. I ran a tap through all of the holes .It may have come out of a 289 Cobra it has the engine number of “549” stamped on the drivers side rear pad. This block would be correct for Cobra , Fairlane , Comet , Falcon , Sunbeam Tiger or any 5 bolt block application . The genuine 289 Hi-Po main caps alone are worth 1200.00-1500.00 . Very hard block to find and if you need one or think you may need a spare for your car don’t pass this up! Winner will pay for truck freight on a small pallet . Good luck bidding!

    On Nov-22-22 at 04:22:21 PST, seller added the following information:

    There are no sleeves in this block. It is just very dirty from sitting for decades. Should clean up at .030 bore

    Original 289 Hi Po engine block 5 bolt 289 Cobra Fairlane C3AE-6015-N | eBay

    -Fred-

    Here is an Ebay auction for a used set of Boss 302 rods by Ebay member "jollyroge" with a starting bid of $0.99:

    Ford 289 Hi-Po Boss 302 Connecting rods Shelby GT350 Cobra. Here is a set of (8) 289 Hi-Po /Boss 302 connecting rods that were removed from a 289 Hi Po engine. Not sure exaclty what the difference is between Boss 302 and 289 Hi Po . They will need reconditioning and new bolts. All have the 3/8” football type head bolt and would be correct for 289 Hi Po’s including all Shelby GT350’s that came with 289 engines. Good rods are getting harder to find . If you need a set of OEM style rods for your 289 Hi-Po engine here is a good set to start with . Winner pays actual UPS shipping charges. Good luck bidding !

    Ford 289 Hi-Po Boss 302 Connecting rods Shelby GT350 Cobra | eBay

    -Fred-

    This set of used set of Boss 302 rods sold November 23, 2022 on Ebay for $594.00 with 32 bids from 9 bidders.

    -Fred-

    Here is an Ebay auction for a used set of Boss 302 rods by Ebay member "jollyroge" with a starting bid of $0.99:

    Ford 289 Hi-Po Boss 302 Connecting rods Shelby GT350 Cobra. Here is a set of (8) 289 Hi-Po /Boss 302 connecting rods that were removed from a 289 Hi Po engine. Not sure exaclty what the difference is between Boss 302 and 289 Hi Po . They will need reconditioning and new bolts. All have the 3/8” football type head bolt and would be correct for 289 Hi Po’s including all Shelby GT350’s that came with 289 engines. Good rods are getting harder to find . If you need a set of OEM style rods for your 289 Hi-Po engine here is a good set to start with . Winner pays actual UPS shipping charges. Good luck bidding !

    Ford 289 Hi-Po Boss 302 Connecting rods Shelby GT350 Cobra | eBay

    -Fred-

    This group of 4 NOS C3OZ 6A527 A rocker arm studs is back on Ebay again with the same starting bid of $119.00:

    1963-1967 Ford Mustang Shelby GT350 Cobra NOS 289 HIPO SCREW-IN ROCKER ARM STUDS | eBay

    -Fred-

    This group of 4 NOS C3OZ 6A527 B rocker arm studs received no bids by November 23, 2022 and therefore did NOT sell.

    -Fred-

    This 65 Mustang Fastback Rangoon Red with black standard interior that was "no longer available" is back on Ebay again as a reserve price auction with a starting bid of $10,000.00:

    1965 Ford Mustang Fastback K - Code | eBay

    -Fred-

    The listing for this 65 Mustang Fastback Rangoon Red with black standard interior was ended by the seller November 23, 2022 with the following explanation "This listing was ended by the seller because the item is no longer available".

    -Fred-

    This 66 Mustang T5 GT convertible white with red pony interior is back on Ebay again with no changes to the Buy-It-Now of $94,981.00 or make offer:

    1966 Ford Mustang T5 Euro Model HI PO 289 Pony Interior Super Nice/RARE | eBay

    -Fred-

    Here is an Ebay auction for a used C3OF-AJ Hipo carburetor by Ebay member "stonemanofwaxhaw" with a Buy-It-Now of $4,200.00 or make offer:

    AUCTION IS FOR ONE (1)

    Autolite 4100 HiPo Carburetor C3OF-AJ

    Date Code A 4 AE = Jan 1964 5th week

    Original to: Ford AC Cobra Shelby Fairlane K Code

    Also Fits: Ford Mustang Shelby Fairlane Cougar Thunderbird

    Very nice original Autolite 4100 HiPo Carburetor C3OF-AJ offered for sale! This is a very rare and hard to find carburetor that was used on the early 289 K Code HiPo engines. This is the early Auto-choke version.

    The Carburetor was disassembled and inspected! It was carefully and gently cleaned, with the preservation of the original finishes and patina in mind. The inside was cleaned and rebuilt using new style needle and seats but keeping the original brass floats. All new gaskets, power valve and diaphragms were installed. The hard to find original float return springs and fuel transfer baffles were also reinstalled. The body and mechanical parts are all original and are in perfect shape!

    Note: The mechanical parts like the throttle shaft and choke shafts appeared to be in excellent condition and were not removed. Original clips and fasteners reused where possible!

    Great candidate for a high-level restoration or use as is and keep the patina!

    Please look over the photos, if you have any questions just ask!

    Shipping is included in the lower 48 states.

    Sold as is, No Returns!

    Buyer should verify if these fit your application before bidding.

    NO RESERVE AUCTION! HAPPY BIDDING!

    GOING THRU MY STUFF IN THE GARAGE & THE ATTIC. LOTS OF RARE & VERY COLLECTIBLE STUFF. MOST OF IT IS IN MINT CONDITION! PLEASE CHECK OUT MY AUCTIONS FOR MORE STUFF INCLUDING NOS & AFTERMARKET CAR PARTS.

    Autolite 4100 HiPo Carburetor C3OF-AJ Ford AC Cobra Shelby Fairlane K Code | eBay

    -Fred-

    This pair of used C3OE heads is back on Ebay again with a new lower starting bid of $1,900.00 and a new lower Buy-It-Now of $2,500.00:

    1963 289 HIPO HEADS 47 CC COMBUSTION 11.7 COMP WITH CORRECT HEAD GASKETS. WILL NOT SHIP* COMES WITH NOS FORD INTAKE VALVES NOS TRW EXHAUST VALVES.

    1963 289 HIPO HEADS 47 CC COMBUSTION 11.7 COMP WITH CORRECT HEAD GASKETS | eBay

    -Fred-

    This restored FoMoCo Hipo distributor is back on Ebay again with the same starting bid of $995.00 and a Buy-It-Now of $1.295.00:

    289 HiPo FoMoCo dual point distributor C50F-12127-E Shelby Mustang Fairlane GT | eBay

    -Fred-

    This 66 Mustang T5 GT convertible white with red pony interior received no bids by November 22, 2022 and therefore did NOT sell.

    -Fred-

    Here is an Ebay auction for a used C5DA bellhousing by Ebay member "cajunzc4" with a Buy-It-Now of $120.00 or make offer:

    This is a Used Aluminum bellhousing For a Small Block FORD. Has C5DA 6394 A cast in. It has a piece BROKE out, see the last picture. If more pictures or dimensions are needed contact me.

    It is being Sold AS-IS with no warranty.

    Only ship to the lower 48 states. Payment to be made within 72 hours of item closing.

    Bellhousing Aluminum Ford C5DA 6394 A Pickup Mustang 289 Vintage Old school | eBay

    -Fred-