Posts by C6ZZKGT

    Merlin is correct that 67 radiators are the same for all 289 engines. Ford did not make a differentiation for A/C or extra cooling. The bottom tank of course would have a cooler for automatic trans cars and none with a manual trans. Ford made up for any cooling differences by using a fan shroud on A/C and Hipo 289 cars as they did in 65 and 66.

    -Fred-

    Here is more fuel for the fire.:) The 8 3/4 and 9 inch gears are interchangeble both directions. Most people are unaware of the fact that there are actually three different axle housings listed for 65 and 66 Hipo Mustangs. C5ZZ 4010 A is 65 only. C5ZZ 4010 B is 66 until 10/1/65 and C5ZZ 4010 C is from 10/1/65. The C5ZZ 4010 C one is the one commonly referred to as the later 66 housing as it looks totally different from the earlier ones. I have had both 65 and early 66 housings and I did not see what if any difference there is in them. A discussion about this would be best in another topic. Ford did not change the axle housing to accomodate the 8 3/4 or 9 inch sizes as the are interchangeable. I had mentioned the 9 3/8 rear end third member as appearing similar to the 9 inch. It does use the same housing gasket as a 9 inch and when you look at the gasket you will notice an extra relief cut in the top and bottom. That is to clear the 9 3/8 ring gear. You actually could put a 9 3/8 third member in your Mustang by match grinding the gasket relief pattern to your housing. Of course your 28 spline axles would not work with the 31 spline differential and the really low basement gears that were available for a 9 3/8 was a 3.50 ratio.

    -Fred-

    Ring gear sizes can get confusing at times. By the time you are done reading this post you will be even more confused but possibly also enlightened as to Fords terminology. All of the following information is based on the Ford parts books. Yes, there is an 8 3/4 ring gear listed from 1957 to 1961. After that the same gear is listed as a 9 inch. An example is a B7AZ 4209 K which is a 4.11 ratio. It starts off as an 8 3/4 until 1962 where it becomes known as a 9 inch. There are several other examples as well. To confuse things even more there was an 8 3/4 rear end in a 69 Galaxie but it was of the integral carrier type with a rear inspection cover. I know there are some sources that list the 8 3/4 rear end for 1965 and 1966 however there is no mention of an 8 3/4 ring gear for 1965 and 1966 in the parts book, only 9 inch. How are we doing now?:)

    -Fred-

    Keep in mind that this thread is related to third members only and not the axle housings. The Mustang axle housings are unique. Only the Galaxie and truck third members are at issue here. All Galaxie and truck 9 inch third member parts are usable all the way down to a six cylinder vehicle.

    -Fred-

    The rear end parts used in Hipo cars were originally Galaxie parts. 1/2 ton trucks would be the same in 65. In 66 some cars and trucks had a 9 3/8 rear end. Although they look similar, the only thing that is the same is the third member to axle housing gasket. They are 31 spline units and I see them all the time on Ebay represented as a 9 inch rear end. I do not know how they get away with it as the buyer gets screwed every time.

    -Fred-

    I will give the seller credit for posting everything that people questioned during the auction. If you look at the bottom of the auction he posted answers to questions on almost a daily basis. He posted the trans tag which turned out to be a correct close ratio, the rear end tag which is for a 9 inch for a 68 Mustang and pulled the valve covers to find non Hipo heads. He fully acknowledged the fact that it had the wrong rear end and non Hipo engine in the answers. I believe that he did not know what he had at the beginning of the auction but was more than willing to disclose everything that other people discovered on the car. He also took up the carpets and took pictures to show the condition of the floor pans. The only thing lacking were pictures of the underside of the car. If buyers read all of the information posted on the auction, there is no excuse for not know exactly what you were or were not getting in this car. I wish the new owner a lot of luck on this project.

    -Fred-

    It would seem that the "K" in the VIN on the block is leading you to believe that this is a Hipo block. The "K" in this VIN indicates that the car was built in Kansas City. It is not for the engine type. My first thought was that the engine was originally in a 71 year car but the 2001 casting number would indicate a 2001 instead. The vibration damper is not thick enough for a Hipo. The four groove crank pulley sounds like a 64 1/2 one for A/C and P/S if it has three retaining bolts in which case it will be a cast one. You need to look at the underside of the heads where the push rods come through for the casting numbers to determine their original application. Hipo heads will have always cast in valve spring pockets and screw in studs. Screw in studs can be added to standard heads but not the cast in valve spring pockets.

    -Fred-

    I saw the 67 fastback at the 2006 SEMA show and I thought that it looked really good. It had a trunk lid and doors. It only needed to add everything unboltable from a donor car and it would be a done deal. I believe the pricing is around $15,000 for the shell but I am open to correction on this.

    -Fred-

    Hi Rene,

    It sounds like the bushings in the clutch and brake pedal support are either worn or missing. Worse case would be that the main bushings in the support are broken loose. There are ball bearing conversions that will fix this problem. It will probably not break and leave you stranded but I would fix it soon so that you do not damage anything further.

    -Fred-

    I just talked with Harris on the phone. This is a "C" code car and he says the engine does have a Hipo VIN. He says that it has the right carburetor and headers but being that he was driving at the time I did not ask specifics on what he meant on the carb or headers. Therefore I do not know if the car has a 4100 and cast manifolds or not. I did not inquire any further than that. This car is advertised as a GT and carefully does not state that the car is a Hipo but only that the engine is a Hipo. This car is neither a "K" nor a GT.

    -Fred-

    If you want to keep your Kar correct, make sure that they do not talk you into a Klone carburetor. It is a regular Galaxie or other one with a 1.12 venturi like the Hipo. They will call it a Hipo conversion and it will not have the choke lever stop that is cast into the base of a Hipo only carb. It will admittedly look nice and drive well but will not be correct. They may have some Hipo cores as I sold them some a couple of years ago. They were not cheap and I am sure that they will pass the expense on to you.

    -Fred-

    Actually the correct date on the above distributor is July, 1965 first week. The A-E codes in the third position indicate weeks of the month. Ford did not use calandar days on FoMoCo distributors. A Motorcraft distributor of a similar number would be 5G30 which would mean that it was built on July 30, 1975. Being a Motorcraft number it could also be 1985 except that by 1985 Ford was using a single point housing with a tin block off for the vacuum advance unit. The numbers on that unit are only on a tin tag screwed down where the vacuum advance unit would have been. There can really be no confusion on this particular date code as being a FoMoCo unit.

    -Fred-

    Any time that you need to spread the shock towers to add a Monte Carlo bar or export brace, it is imperative that you realign the front end. It will definitely put more positive camber in the front end and probably unequally. Most Mustangs that I have added these pieces to have always needed some help with spreading the shock towers. They just sag inward from age as there is not enough support from the factory for them.

    -Fred-