This Kar is now relisted on Ebay twice at the same time. It has a starting price of $24,500 in one auction and $25,000 in the other auction.
-Fred-
This Kar is now relisted on Ebay twice at the same time. It has a starting price of $24,500 in one auction and $25,000 in the other auction.
-Fred-
Make sure that you bring some tools along to help check whether this is a real Hipo engine or not. It is not that tough to drop the oil pan enough to look at the short block.
-Fred-
At least the heads are correct.
-Fred-
The two groove water pump pulley is a cast iron piece and looks like one for a 63 260 or 289 with A/C. The lower one has three grooves but it is hard to tell if it is cast iron or not. Keep in mind that a stamped steel three groove C5AE or C5OE pulley will not fit into a C5OE balancer. It will only fit if the balancer is machined out slightly internally to accomodate the pulley. The C8ZE replacement balancer however will work with a three groove pulley. It is really hard to tell from the picture but the balancer may well be a C8ZE one.
-Fred-
He seems to be basing his price on his own idea that "done K codes are fetching in the high 70's to 80 thousands". I seem to have missed seeing any of these going for that kind of money as yet.
-Fred-
The passenger side exhaust manifold is a 63-64 Hipo Fairlane piece.
-Fred-
Duke,
I am happy that everything worked out well for you on the radiator flush. You still need to consider the Gano filter to keep this from happening again.
-Fred-
Duke,
Keep in mind that the rust that you see inside the radiator is a small percentage of what is actually there because you are only able to see the small area around the cap opening. After you have your system flushed out you will still need that Gano filter to preclude this happening again. The only upkeep after that will be to clean the filter once in a while. You may still need to remove the radiator to get it rodded out as the rust clumps will pack themselves inside the radiator tubes, especially if you have a three row with small tubes.
-Fred-
Generally if you have a hole above the choke cable hole it will be for the neutral safety switch wiring with an automatic trans. Being that you have a 65, the automatic trans is not possible so this may be a mystery hole. You can post a picture of your firewall on here and possibly get an answer.
-Fred-
Both of my 66 San Jose Kars have the hole almost directly behind the accelerator linkage. If you had the rod to the carburetor off and pivoted the linkage back to the firewall, it would almost hit the hole. There is no grommet as Ford just used caulking in the hole.
-Fred-
Jim is correct about the 91160 number as they all seem to have that number. I was referring to the C3OA-C number to clarify the type of fan. Some fans have both the C3OA-C number and the 91160 with a date code. To further confuse the issue, I have a repro fan with a C3OA-C number on it however an original will be in fairly large letters and have a FoMoCo logo on it as well. I am pretty sure that I have seen an early repro with the 91160 number. Someone else on the board may have one to verify this. The shape of the blades where they attach to the center spider is the clue to originality and can be seen in a decent picture.
-Fred-
The seller has cancelled the auction.
-Fred-
You should have a C3OA-C fan blade.
-Fred-
This fan is actually for a 69 or 70 200 inch 6 cylinder Mustang and should measure 16 inches in diameter. The correct one for a 67 Hipo Mustang is a C6OE-D that is 17 1/8 inches in diameter. The correct one for a 65 and 66 Hipo Mustang will be marked C3OA-C and be 16 inches in diameter. There were some early 67 Hipos that had the C3OA type from what I have been told. I have one with a J6 date code.
-Fred-
The seller has sent me an email regarding this car. He states that the previous owner changed this Kar to a pony interior and changed the tags to match this. He is supposed to be getting the original tags and part of the window sticker from the previous owner. This verifies our thoughts on whether the tags are original or not. I have also received some underside pictures of this Kar and it looks pretty good.
-Fred-
It is also interesting in Bobs' picture above that the C3OE number on the rear main cap appears to have the three stamped into it rather than cast in like the others.
-Fred-
In regards to the overflow bottle, I have used the 67 blow molded type of winshield washer bottle as an overflow tank. I mount it close to the shock tower on the left front inner apron as it is angled to fit there. I move the original washer bag and bracket forward. At least it looks more like a factory piece.
-Fred-
I have several sets with the arrows on the side like the Mexican caps in the picture. Bobs' picture with the arrows in the center is the first example that I have seen.
-Fred-
The spare tire hold down bolt is longer for a styled steel wheel so that it can be mounted face up. I believe that Charles Turner will concur with me on this. I also have a smaller diameter spare tire hold down clamp that I use on styled steel wheels which I believe to be correct although it may be for a later year.
-Fred-
Duke,
You have not stated that you have looked inside the radiator with the cap off as yet. I have experienced a plugged radiator with very short running times just by the leftover loose rust in the block. You have stated that the coolant turns brown from rust so I still think a plugged radiator is a strong possiblity. If you have a three or four core radiator with the smaller than standard tubes, this will trap rust even faster. The radiator will normally build up a certain amount of pressure and when shut off can puke out enough coolant to need a refill to keep from overheating.
-Fred-