Posts by C6ZZKGT

    With deep stress or heat cracks, I would not even consider using this flywheel in a lawn mower. I have been in a car with a flywheel that had known deep heat cracks many years ago and the flywheel exploded which destroyed the car and engine. I am lucky to be able to tell the tale as I was a passenger in the vehicle and it was going about 70 miles per hour down a slight grade at the time. It ballooned the dash, cut the frame and brake lines, broke the block, dropped the trans on the parking brake and then I had to keep the driver from jumping out while I ran the car into curbs to stop it. That used up over a mile of distance. It was fortunate that I did not encounter any traffic problems during that incident. Either throw it away or mount it somewhere as a display so that you will save your car and possibly your life.

    -Fred-

    There is only one three row radiator listed for the 65 and 66 model year Mustangs. It was for 66 only with V8 and A/C only and only before 1/5/66. After that they went back to the two row for all V8 65 and 66 Mustangs. The radiator looks like a gypo 4 row due to the larger squared off looking top tank. It has a Mc-E 5 reversed stamped into the top tank near the filler opening. It has a C6ZE-A reversed stamped into the left side mounting bracket near the top. This radiator does not use fan shroud brackets as the shroud bolts directly to the radiator. The shroud is also different as it is not relieved to clear the top tank like the other shrouds. The fan shroud is a C6ZZ 8146 A and also requires a shorter fan clutch than other cars. It is a C6ZZ 8A616 A as the radiator is 2 1/4 inch thick rather than the 1 1/4 standard radiator. You will not find this radiator number in your 1975 final edition Ford parts catalog as this was obsolete for too long by 1975. There is not even a cross reference to this number in the radiator identifier at the beginning of the radiator section. The only reason that I have this radiator number is that I saved a Ford catalog that has not been updated since 1970. Therefore most of the older numbers, including some obscure accessorires like snow tires, rally packs and AM-FM radios are listed in there.

    -Fred-

    Hi Bob,

    Welcome to the Hipo forum. I too am a big fan of your book. I have personally had seven Hipo Mustangs and three Hipo Fairlanes. I still have two Hipo Mustangs and one Hipo Fairlane. I have steered a number of people your way to buy your "bible" book. I am thankful that you put so much effort and dedication into your book. Some of the information in your book seems to be unattainable anywhere else.

    -Fred-

    In response to some comments about this car, the door shell is not a repro and the engine VIN above the pan rail has now had the paint cleaned off and it matches the Kar. The engine has a replacement C8ZE Hipo balancer. The engine has a hydraulic camshaft. The rear end housing is correct and has reinforcement plates welded to the housing at the spring brackets. The Kar was raced in a previous life and this is a common modification to keep the axle housing from spinning on the spring mounting plates. The plates can be easily removed. The rear end center section is a later model piece with a fill plug and has the original 66 snubber. It has a repro fan and exhaust manifolds. The right side fender aprons are original and the VIN is intact and correct as read from underneath the aprons.

    -Fred-

    Here is just a little more information about blocker rings and synchros. I have been rebuilding 4 speeds for over 40 years now and there are some misperceptions regarding some symptoms and cures. Blocker rings are named that because that is what they do. They are made to move about 1/2 tooth off from straight so that the synchro slider drum has to hit the teeth on the blocker ring. When that happens it pushes the blocker ring, which has a cone shape inside matching the gear, against the gear causing the gear turn at the same speed as the synchro drum. Thus the gear is synchronized in speed making the shift quiet. The blocker ring has no other purpose. The small teeth on the speed gears and the synchro drums are the major culprit when having the trans fall out of gear. They both get worn when you hear the trans grind and after enough times the teeth are too worn down to keep it in gear. Replacing the synchro assembly only can sometimes fix this if the drum is fairly worn but the gear usually wears more. This makes gear replacement necessary to correct the problem. As you can imagine, this can add up quickly in costs as you usually need both 2nd and 3rd gears. That means two synchro assemblies and two gears in most cases. The first gear usually holds up well as it is only used for downshifting. Sometimes the main drive gear also is worn beyond use. Another sometimes over looked area is that shift forks can wear against the synchro drum causing a loose fit and requiring replacement of the forks as well. I hope this gives a better understanding of some 4 speed problems.

    -Fred-

    Lyle,

    From your description, these are typical modifications to strenghten the Z bar when using a stiffer than stock clutch. With some work the extra metal can be removed to make it appear stock again. I have had a couple of these beefed up ones like that before. A friend of mine bought a 66 Hipo coupe new and raced it at the drags exclusively for years. He beefed up his Z bar for the same reason of a stiff clutch. The clutch was so stiff that when he pushed it down you could watch the firewall flex if you watched from under the hood.

    -Fred-

    When my friend bought this 65 Comet Cyclone 20 years ago he paid $400 for it as it was dripping water out of the exhaust pipe due to a blown head gasket. He had no idea what the car was and neither did I at the time. Being as I was the one to work on the car I was surprised to see what appeared to be a Hipo 289 under the hood. I looked at the toploader trans and 9 inch rear and assumed at the time that this was a transplanted drivetrain from a Hipo Mustang as the rear end has the tapered axle housing unlike the Fairlane version. About a year later I was working on the drivers window replacing rollers when I found the build sheet stuck to the inside of the door panel. I usually store all of his paperwork as he tends to misplace things as he did this build sheet in relocating his residence a few years after selling the car. I have seen another Hipo Comet build sheet since that time and it had far less info than his did. I do remember that it mentioned the 271 HP engine, special driveshaft, special trans, special rear end and something about the export brace but they called it something else on the build sheet. I do not remember it mentioning a Daytona package and I am pretty sure that I would have remembered that. The firewall has an added reinforcement plate welded below the lip where the export brace bolts on. It is an A code car with a 6 digit DSO. It was built in Los Angeles for the Los Angeles district so it has never really left home.

    -Fred-

    I dealt with a similar lack of integrity regarding another car from this forum about 2 months ago. The car was only 3 1/2 hours away from me and he knew that I was paying cash. He kept putting me off and then told me that he sold it to someone in Europe even though we had an agreement. Personally I believe that the guy was possibly misrepresenting the car and knew that I would pick up on it so he did not want me to see it. That is only a supposition but I really believe it to be true.

    -Fred-

    A friend of mine has an original 65 Hipo Cyclone. I am unclear as to his being a Daytona package as the build sheet only called out for substituting the 271 HP engine among other things. He bought it over 20 years ago, sold it in a year or so after that and bought it back a couple of years ago. I was just tinkering with it last week and will probably be back on it again later this week. He likes freeway driving and the 3.89 gears really did not cut it for that so he changed it to a 2.88 gear today.

    -Fred-

    Bob Mannels great book on small block Fords is available dirctly from Bob for only $35.00 plus $5 S&H. You can call him at 423-245-6678 in Tennessee. His address is RPM PRESS; 340 Clicktown Road; Church Hill, TN 37642-5522. Anybody who thinks that they are a Ford gearhead needs this book. You will need to build up your upper body strength to lift it though as it is an inch and a half thick like a medium sized phone book.:)

    -Fred-

    The keyway is not aligned with the TDC mark on the balancer. However, if you align the balancer TDC mark to the timing cover pointer the keyway will be at 12 'o' clock. Most vibrations that I have encountered relating to balance issues showed up at mid to high RPM. I had a vibration at mid and higher RPM's on mine. I too suspected that the balancer outer ring had slipped. When I went to remove it the balancer came off with no more effort than pulling on it with my hands. It turned out that the snout was cracked enough front to rear to break a section out of it. As long as it was bolted on it stayed together and still sealed without leaking oil. It was not salvageable once removed and the crack in the snout was making the balancer have a slight wobble causing the vibration. So much for a tough to find C5OE balancer. All this said, I realized that even if the ring had slipped, the only problem would have been the timing mark because it is the same mass all the way around. If your balancer has not been drilled for balancing on the outer ring, the position of the ring is not going to affect the balance. However, I see many balancers that are balanced after the original production during a rebuild that have been drilled for balancing the engine. Worse yet I have seen balancers drilled almost to the point of being ugly to create a balance without the front counterweight. Those would definitely cause a problem if they slip.

    -Fred-

    The upper and lower sprockets in a Hipo 289 are in the same position relative to the block as other 221, 260, 289, 302 and 351W engines. The timing chain on 221, 260 and early 65 289 non Hipo engines is the earlier wider version. All Hipo 289 engines used the narrower chain that also came into use on all later 289, 302 and 351W engines. The narrower chain was used on all 63-67 Hipo 289's to allow for the counterweight. The upper sprocket on the late 65 Hipo 289 and all later 289, 302 and 351W engines are the same. If you measure a counterweight and lower Hipo sprocket together, they come out to the same thickness as a standard non Hipo lower sprocket. This of course changed with the introduction of double roller chains and sprockets by Ford in the 80's. All this said, it would be feasable to use a double roller chain setup if the chain is the same width as the original narrower silent chain. The lower sprocket would need to be narrowed to accomodate the counterweight and the locater pin hole drilled. I have a counterweight that was in a 64 1/2 Hipo 289 where some unknowledgeable mechanic had installed a wide chain. It had a really decorative wear pattern on the face of the counterweight from the wider chain where they contacted one another as the chain moved fore and aft on the sprockets. I would guess that they or the parts place that sold the parts did not know about the differences in the Hipo 289 chain. This engine also had 2 standard 289 rods probably for the same reason.

    -Fred-

    Another change from 2V to 4V was in the pistons. 289 4V regular fuel versions had the same dish top pistons as the 2V version. The 289 4V premium fuel used flat top pistons in early 65 and added valve reliefs to the flat top pistons later in the year. This gives the 4V premium fuel version a higher compression ratio and more horsepower.

    -Fred-