It is indeed possible that this was a theft recovery at one point a long time ago. That would explain it being picked clean.
-Fred-
It is indeed possible that this was a theft recovery at one point a long time ago. That would explain it being picked clean.
-Fred-
In 1965 the pony interior option also gave you the five dial instument cluster. It was not GT specific. The difference in the cluster for GT and pony interior was in the camera case or woodgrain bezel. The fact that the door hinge post does not have a hole for the door light wiring means it was not a pony interior car. Therefore it must have been a GT in its previous life.
-Fred-
The cast frame mounts are different on a Hipo as they are deeper to allow for the extra parts used in the mount assembly. That way the engine sits at a proper height. The casting numbers begin with a C4ZA rather than the C3DA for the standard cast frame mounts.
-Fred-
The 66 Galaxie wood grain wheel will work on a 65 or 66 Mustang but the 67 Mustang wheel has thinner spokes and is not the same. A 67 Galaxie wood grain wheel will fit a 67 Mustang as it is the same part.
-Fred-
The markings on the core support look like a painted on version of the buck tag. I have never seen these before. Great job of documentation!
-Fred-
I am unfamiliar with TRW numbers however a 289 and 302, except Boss 302, use the same piston. The difference in the stroke is made up by the shorter rod on the standard 302. Ford did not relocate the pin hole on a standard 302.
-Fred-
Hipo 289 valve stem seals are not the same part number as a standard 289. 65-66 uses C3OZ 6571 B and 67 uses C3OZ 6571 C.
-Fred-
The C9OZ 6250 A is just a standard passenger car camshaft.
-Fred-
Lyle,
If you have not spun the nut in the frame, you can drill the bolt out carefully and retap the nut. The process of drilling it out in stages will sometimes break the bolt loose. The bolt does not bottom out as you can see by looking at the other side where you already have the bolt out.
-Fred-
A Pony carburetors Hipo conversion carburetor (clone) is $669.50 outright plus shipping.
-Fred-
Chuck,
Based on the Ford parts book and the Muscle parts book supplement number 1, the following is the best information that I have:
C9ZZ-6250-A 1969 Boss 302 markings are upside down A with an EB
D0ZZ-6250-A 1970 Boss 302 markings are upside down A with an ED
Basically the markings are the same as our Hipo 289 cam with an additional suffix. I cannot figure out a way to make an upside down A on a computer. I could find no reference to paint colors. The interesting thing about the Boss 302 camshafts is that they are identical in specs to each other. I do not know what other physical differences may exist however by 1980 the 69 camshaft was replaced with the 70 camshaft by Ford. The Boss 302 camshaft has far less duration than the Hipo 289 camshaft at 290 degrees compared to our 310 degrees.
-Fred-
I have an NOS C5ZZ 10B960C 8K Rally Pack still in the Ford box. This is definitely a dealer installed version and it has FORD on the tach and a blank plate between the tach and clock. This should help determine with certainty which were factory versus dealer installed versions.
-Fred-
Ron,
The 4896S is a D0AZ 9350 B and fits a 1970 302 2V only.
-Fred-
Ron,
I looked at the pictures on your Ebay auction #190102406253. This appears to have possibly been an older rebuilt pump as the original would have had the second spring on the arm. Rebuilders are notorious for using anything that will work for what they are building. They are not really concerned with numbers.
-Fred-
Mark,
You can use the later style cam sprocket by eliminating the spacer and changing the retainer plate to the later style along with the retainer bolts. Make sure that you save the old retainer, spacer and bolts as they are early Hipo specific parts.
-Fred-
The WCZ-S tag decodes to a 66 Mustang 9 inch 3.50 ratio non-locking.
-Fred-
The HBG-F2 rear end is from a 64 F100 pickup truck with medium size carrier bearings which are the same as a 65-66 Hipo Mustang 9 inch.
-Fred-
I had 6T08K107076 and the production date was September 3, 1965. It had an HEH-BX trans.
-Fred-
I had the same experiences as Charles did with doing other things while the pages opened. I am very happy to see that the site is now working well.
-Fred-
I usually have all of my drive shafts retubed during restorations because you end up with a new looking shaft rather than a pitted and cleaned up one.
-Fred-