Posts by C6ZZKGT

    A couple of things bother me about the GT status of this car. The fog light switch is in the later production location rather than hanging under the dash and the drivers side fog light wires come through the core support which is unlike the early ones that I have seen wrapped around through the headlight area. It just looks to me like someone wanted to make it look correct and was unaware of how the early GT's were done. I would love to see the dash cutout behind the instrument cluster.

    -Fred-

    SPECIAL ED is certainly on the right track with the WD40 as long as the reset coil is not burned out and the points are good. When I was a parts manager we used to send clocks out to a Ford approved clock repair place. They told me that heating an oven to 200 degees and turning it off before putting the clock in would reflow the grease and get it going again most of the time. They did this with most of the clocks that they serviced. I have used this idea myself with success most of the time. The WD 40 tends to at least loosen up the grease and will help as well. If the reset coil is still good a simple filing of the points will get them working again as well.

    -Fred-

    Very nice looking Kar Chuck. You might want to note that the carb is not truly the "correct" carb as it is a Hipo clone. This is based on the fact that the cast in choke lever stop is not present on the carb body and the air tube for the automatic choke in the carb top should not be there.

    -Fred-

    David,

    The one that you see on Ebay is #270132618556. It is not even close to correct. Please review the previous threads posted in the post prior to this one of mine.

    -Fred-

    Hipo 289 rod bearings are a C3OZ part number where the standard bearings are a C2OZ part number. The Hipo rod bearings are of a tougher material than the standard 289 rod bearing. It would be equivalent to a Clevite 77 bearing.

    -Fred-

    Hipo 289 rod bearings are a C3OZ part number where the standard bearings are a C2OZ part number. The Hipo rod bearings are of a tougher material than the standard 289 rod bearing. It would be equivalent to a Clevite 77 bearing.

    -Fred-

    If your cable has streched, a common problem, I have been successful in adding a flat washer between the shift handle and the shifter mechanism for both bolts. Sometimes if the cable is stretched enough you might need two washers for each bolt. This raises the shifter up enough for the tab to then clear the tower when you pull up on the lockout. There is no downside to this fix. It is just a free fix unless you actually need to go out and buy the washers. Then it may cost you 25 cents plus tax. This will buy you time until the cable completely fails, however mine has been like this for 20 years.

    -Fred-

    Parts, including blocks, are not date coded like the 65 Mustangs as they were strictly by calendar year. Your block is actually March 12, 1965 and not 1964. The block that you have certainly falls within the build parameters at the time. To make it totally correct you should be checking for the VIN stamped in the block.

    -Fred-

    Disc brakes did not have power assist until 1967 on Mustangs. The disc brake master cylinder does not clear the shock tower brace with the Mustang power brake setup. I have added power disc brakes on a 66 Mustang with the Mustang setup and needed to use an export brace to clear the master cylinder. Even then the master cylinder cap still rubbed on the brace. There are aftermarket power brake systems on the market now that will clear even a dual master cylinder on an early Mustang. I have installed these with good success.

    -Fred-

    David Kee's directory is defintely in error on this one as the Ford parts manual clearly states that an HEH-BT is for a standard 289 from 2-1-65. There are three other tag codes listed for cars built prior to this. If you look closer at the David Kee directory you will notice that there is not a Hipo trans listed prior to the 2-1-65 date other than the HEH-T which lists from 8-20-64 to 10-1-64. There is a listing in the David Kee directory for the HEH-BR for a standard 289 as one of the trans codes prior to 2-1-65. I use the David Kee directory a lot as it save me the trouble of opening my parts manuals as they are heavy and awkward to move around. This is only one of two errors that I have encounterd in the David Kee directory so far. They are only human and they are just trying to provide a service to all of us. We have also found out through this forum that the HEH-T was used long after the Ford manual stated that it was.

    -Fred-

    The F-O-R-D was used on the T-5 hoods as the only word that was a problem was MUSTANG. The cars were considered to be Ford T-5's. In 67 and 68 they also put FORD letters next to the T-5 badge on the front fenders.

    -Fred-

    Ford listed a C7AZ 1130 H cover for a 67 Mustang except GT350/500. It is a 15 inch wire spoke cover with a spinner and a blue center. This was originally for a 67 full size Ford as well. There is no listing for a wire cover for a 67 Thunderbird. The first Thunderbird wire cover is in 1968.

    -Fred-

    I had a customer with one of these a couple of years ago. It reminded me of a small version of a 70 Torino except for the right hand drive. The master cylinder was quite small for being a dual cylinder. It had a 351 Cleveland and was a blast to drive around town sitting on the wrong side.

    -Fred-