Mike
You are one number short on the VIN. I am surprised that it is even an "A" code car. The only thing on the engine that I can see that makes it a Hipo is..................nothing!
-Fred-
Mike
You are one number short on the VIN. I am surprised that it is even an "A" code car. The only thing on the engine that I can see that makes it a Hipo is..................nothing!
-Fred-
The seller of this block is now aware that it is not really a Hipo block and that the caps are Mexican ones. He was unaware of the differences until they were pointed out. He is an Ebay seller with integrity and has relisted the block as a standard block with Mexican caps with a much lower price. On the plus side, it is a standard bore 5 bolt block.
-Fred-
The rear cap is not a standard cap as the finish is correct for a Hipo or Mexican cap. The standard cap has a definite step in the surface that is concentric with the main bearing shape. The fact that there are no numbers at all on the rear cap leads me to believe that these are disguised Mexican caps as all of you are already thinking. It surprises me that the main cap bolts are not the correct type as they are certainly not tough to find.
-Fred-
In response to KAPDAVM, the axle housing can be correct for an early 66 Kar. It should also have the early Hipo motor mounts but it does not have them. The reason that I say that is that one of my Kars is a December 1, 1965 Kar and it does have the early Hipo mounts although according to the Ford parts book the change to the standard mount was November 1, 1965. This Kar has a replacement C8ZE balancer, a Gypo air cleaner and export brace and a generic Holley carb. If you look at the pictures in the actual auction you will get a kick out of the park brake return spring. It is stuck into one of the seat access plugs. It appears to me that the front to rear frame rails at the trans crossmember were replaced and they did not drill the holes for the brake return spring. That would explain the odd placement of the spring. It appears that the undercar detail was done by just painting everything with primer including the brake lines and cables. No effort was made to remove or mask anything. The original interior is a nice touch but the hole in the side of the drivers seat would warrant replacement or at least a repair in my eyes.
-Fred-
Big Al,
This Kar was just recently bought from the states by Tony so it is unlikely that Peter S. owned this particular Kar.
-Fred-
I have NOS Ford intake gaskests that are white and apparently made by Raybestos as that is the purple ink stamping on them.
-Fred-
I had a repro fan on my 65 Hipo Fairlane sports coupe and it worked well without any vibrations. They look quite similar to an original but anyone who really knows the difference can tell a repro from just a picture. It is not necessary to get up close and personal to tell as the repro does have a very subtle difference in the shape of the blades.
-Fred-
The build date does not seem to go with the VIN and the door tag is a reproduction.
-Fred-
The C3AE rods with football shape bolt heads are actually Boss 302 rods which are Hipo 289 replacement rods from Ford.
-Fred-
The 406 and 427 generator pulleys are both of the same larger diameter as the Hipo 289 but are not the same.
-Fred-
The block that goes with this car is not an October 64 date but rather an April 64 date and also it is a 5 bolt block which will not work.
-Fred-
The 10-64 transverse muffler has FoMoCo in block letters where the 12-65 has the Ford oval. The 12-65 is just a later service part however it is the first one that I have seen with that late of a date code. Both of these are free of any corrosion.
-Fred-
The only picture that I have of an Arvinode system is for a 65 Fairlane Hipo and it only goes to the rear axle. The Arvinode system went with my 65 Hipo Fairlane sports coupe when I sold it. I am sure that the new owner has not installed it as yet so I can probably get a picture of the rear part as well if there is a need. Just as a side note, I do have a couple of NOS Hipo transverse mufflers that I came across recently. They are date coded for 10-64 and 12-65.
-Fred-
There is also an actual shift shaft seal plus the "O" ring. The seal is the more likely of the two to leak. In order to replace the seal you need to drop the trans pan as you will need to remove the nut on the shift shaft and pull out the shift shaft to replace the seal. It is not that tough of a job but it can be a very messy one.
-Fred-
Dave,
If you seldom drive the kar and the rear end is quiet, I would leave it alone with the exception of the seal. It is tough to duplicate the factory setup exactly after changing the bearings to preclude noise issues. The ring and pinion pattern can be more critical than you might think. It is kind of like trying to paint a panel on your kar to match faded paint. The pinion bearings are the typical bearings to fail and they can be replaced without removing the rear end if they should fail at a later time. However, this is just my personal opinion. If you need any guidance, just give me a call.
-Fred-
The trim code of 26 is for a standard black interior and does not go with the 63B body style. It is listed in the registry as a 63A which is correct for a standard interior. The DSO in the registry is a 53 where it is a 55 in the auction. These changes cloud the authenticity of the rest of the car such as the GT status. It was at least built at the right time to possibly be a GT, though. A look at the cutout around the instrument cluster would help to clear that up.
-Fred-
More details on the differences between the carburetors is available on page C-13 of Bob Mannels small block Ford book. It gives you not only jet sizes but venturi booster numbers as well. For engine information this book far surpasses any other Ford available publication.
-Fred-
I concur with RalphJr in regards to the Ford and Mustang words on the tach and Rally-Pac on the bridge. I have an NOS C5ZZ 10B960 C 8K Rally-Pac in the Ford box and it has Ford on the tach with a blank bridge. However I do have a number of used 8K Rally-Pacs that have the word Ford on the tach and Rally-Pac on the bridge. I also have a used 8K Rally-Pac with Mustang on the tach and Rally-Pac on the bridge. I do not ever recall seeing one with the word Mustang on the tach with a blank bridge. All of this could of course also be affected by replacement tach heads or conversions from 6K to 8K in later life. I do believe with the number of these that I have that most of them are original.
-Fred-
The buyer is now a new member of this forum. He has already posted looking for some direction on this purchase.
-Fred-
If you are truly losing the timing after a few times of trying to start it there is a strong possibility that you have sheared the roll pin that goes through the distributor gear and the shaft. It will look complete even when broken but the shaft will not turn with the gear all of the time. This could have been this way before you installed your distributor and it would not have been necessarilly obvious. It is usually caused by the oil pump seizing up due to foriegn particles like broken nylon capped camshaft sprockets getting wedged in the oil pump gears. That will usually twist the oil pump drive rod like a barber pole but can also break the distributor gear roll pin. This could have happened long before you owned the distributor.
-Fred-