Posts by C6ZZKGT

    I did the T-5 swap for a customer a couple of years ago. The shifter comes out fine however the clutch linkage relied on a cable setup with a late model bellhousing to match the T-5 trans. It was a conversion kit that was used on the car. I never tried to use a stock vintage bellhousing with a T-5 trans. There is most likely some way to adapt it so that you can use your original clutch linkage but I have never tried.

    -Fred-

    Your center section was cast on November 2, 1965 based on your casting date code. That fits in nicely with your rear end tag and scheduled build date for the Kar. Is it possible that your door tag is a reproduction? They have been produced for a long time now and are easy to spot when you are aware of the differences. If you post a picture here of your door tag or email me a picture it can be easily be determined as to what you have.

    -Fred-

    Are you speaking about the full set of lines and numbers as indicating 5,10,15, etc. on an 8K low profile tach? If that is the case, Ford did make some of them like this. The lines and numbers are so busy that it is hard to read where the needle is on the tach. I have had a couple of these 8K low profile units that were indexed this way. I also have an NOS low profile Rally Pac tach that is indexed this way.

    -Fred-

    In the original ad on this Kar the seller states that he does have the original core support and ID panel, which I will assume to be the LH fender apron. He also stated that he has the door tag. I did not see anything regarding a title but at least the important metal ID pieces are there. His price has also come down from the $14,000 in the original ad.

    -Fred-

    I just looked again at the Ebay auction Dave and this is one of the statements in the auction.


    "Car has NEVER been restored !! Has the Normal rust on both torque boxes , rear inner and outer wheelhouses , Framerails & Floorboards."


    It sure sounds like it will need more than just a fuel line and fuel tank to me. "Normal rust" to me sounds like the carpet is now the floor and good luck on opening and closing the doors. I could, of course, be wrong on this. It is just a mental picture that I have. As bad as my Hipo GT T-5 convertible was, even it did not need a fuel line. I believe that the paint on my Kar was the strongest part of the Kar as the metal certainly was not. :) How bad does a car have to get before it rots out the fuel line? I am sure glad that I am in California as I would truly hate to see good cars just disintegate from rust.

    -Fred-

    I agree with Dave on the unrestored part however the rust tends to scare me away. I already went through all of the rust issues on a 66 Hipo GT T5 convertible that I had many years ago. The doors would only open when you were outside the Kar. If you were inside it involved a lot of shoving to get the doors open. I did however fly my wife and son back to Georgia with me so that we three could pick this Kar up and take it home by driving it cross country to California. Does that take guts or what? At least my Kar was more or less driveable whereas the one in this auction is definitely not as it is now. My Kar came out really nice but it was a lot of work. There are many people on this forum who are working with rust issues as well and the expense can be a killer.

    -Fred-

    I sold a restored 65 Hipo GT fastback to a buyer that was really not a Kar guy years ago. His first gripe was that it did not have a windshield washer system. I explained to him that it was optional in 65 and that I would add one if he wanted it. I also told him that if he drove the Kar long enough to get the windshield dirty enough to need the washer that he should be ashamed of himself. He chose to not install the washer. :)

    -Fred-

    Your Kar is near the Ford transition date to the newer style 66 axle housing. It indeed could be the original housing and have had the center section changed. Look for a date code cast into the center section near the passenger side upper section of the casting. That will help determine if the center section is correct.

    -Fred-