I have sent you both an email and a PM on this.
-Fred-
I have sent you both an email and a PM on this.
-Fred-
Tim, Al is not the seller. He merely posted the Craigs list ad for us to see. You will need to contact the seller. The ad link is in the post. With an early 66 date code they will not be Hipo heads.
-Fred-
Bob, I sent the email to your jacsinc email address that you have registered with this forum. My email address and phone number are also in the message that I sent to your private message mailbox on this forum.
-Fred-
I just sent you both an email and a PM.
-Fred-
I just sent you both an email and a PM.
-Fred-
It appears from the auction that you have already bought it for $72,000. Have you paid them yet?
-Fred-
Merlyn, I just sent you pictures of the 66 style that is done.
-Fred-
The red color coordinates very well with the Rotunda oil filter.
-Fred-
That is a valid point as far as the original owner getting the car back, Bill. Either way it still does not belong to the girl.
-Fred-
Well said Don!! I am sure that if someone on this board lost their Kar that they would feel the same.
-Fred-
Great looking car and background!!
-Fred-
This Kar has been discussed here before but I cannot find it even in the archives. The first time I encountetred the Kar it was in North Carolina or Tennessee as I recall. This was about 6 years ago. I was considering buying it myself at the time as it was only $20,000. It just had to many discrepancies from original at that time. It had an 8 inch rear end at the time. It was definitely a pony interior conversion at that time. The GT status was also in question. The seller is Joe and I spoke with him yesterday and he is being as honest as possible on this Kar. He goes even further in stating that he believes that it is a rebody and is selling it as such. I have never actually inspected this Kar so I cannot say if the rebody statement is true or not however he really believes that it is. He is honest about the door tag being changed as he himself did it since he owned the Kar and does have the old one. He is not even sure that the old one is original either as he says that it looks too new. He also states that it is dealer added GT package so I truly believe that he is not trying to misrepresent anything about this Kar. As far as I can see the car was originally a non GT with a standard interior.
-Fred-
Check the thread under Restoration as this is fully addressed there. The bottom line is I am currently gathering up these pumps for rebuild and if you need one done you will need to contact me. I also sent you an email and a PM.
-Fred-
This Kar has the incorrect Pally-Pac.
-Fred-
A friend of mine had an aftermarket pan from Branda and he had the same problem. They are somewhat obvious as the oil pan bolt holes do not line up with the raised surface for them and the indentation of the vertical ribs are not lined up either.
-Fred-
Dave, I have had the same problem with forum emails however I just forward them to the email address that shows in the failure notice and everything works out fine.
-Fred-
Dave, I have not received an email from you however I did send you an email and a reply to your PM.
-Fred-
Lyle, What looks like a red sticker on the heater box is the resistor for the three speed heater blower motor.
-Fred-
The narrow one is a Motorcraft FL295 but it is not shorter, only smaller in diameter.
-Fred-
The fuel pump rebuilding process is not an economical deal. I am just thankful that they can be done at all. Everyone wants to know costs and I do not blame them. The pumps are costing $200 each by the time they are disassebled, tin sent back to me for plating, getting the plating done and sending them back to the rebuilders for reassembly. They do end up with some marks around the area of the tin where they are crimped. This happens when they are disassembled and after plating and reassembly they are not that bad but will still show to some degree. I am reasonably sure that when Ford rebuilt these back in the day, that they were probably using new tin so that they did not have to deal with plating. I have seen some non Ford rebuilt pumps that had very noticeable marks from disassembly. I have come up with a way of marking the pumps to keep all of the pieces going back on the same pumps and getting back to their original owners. Another forum member, Bob, came up with it and it is pretty simple. I will mark the pump body on the mounting gasket surface and the tin on the inlet hose nipple. These marks will be covered by the gasket and the hose when installed so they will not show.
-Fred-