Actually, 289 Hipo rockers are the same as standard rockers through 1965. The change to rail rockers for standard cars came in 1966 and the hipos still used the previous standard rockers without the rails.
-Fred-
Actually, 289 Hipo rockers are the same as standard rockers through 1965. The change to rail rockers for standard cars came in 1966 and the hipos still used the previous standard rockers without the rails.
-Fred-
This appears to be a fairly good looking Kar. However, for the amount of money asked for this Kar, I would expect a little more than I see. At the minimum the idler arm and tie rod ends are aftermarket pieces. The rear end housing appears to be a clone. The harmonic balancer is painted blue. I thought that they were supposed to be black. The scheduled build date for the Kar was January 20, 1966 however the engine date code is April 14, 1966. It supposedly has the proper VIN stamp on the engine. Is this one of the Hipo cars that were built and sat waiting for an engine due to engine shortages? Over 3 months of waiting does not seem to make sense. It is confusing that the ad mentions that it has the original 4100 carb, which it does, and then further down it says that has Holley 780 which it does not. It has a replacement fuel pump. The undercarriage appears to be mostly body color but I suppose that it could be just the camera angles and lighting. It does not have a matching spare tire and wheel. The shocks are white rather than black. It has an aftermarket clutch equalizer bar. I mention all of this because they say that this is an MCA quality trailered show car. I am sure that Charles would see far more than I have.
-Fred-
This Kar has a C8ZE replacement harmonic balancer.
-Fred-
I am surprised that the seller did not mention the original AM-FM radio as mentioned in the earlier auction as it is still these. That would seem to be a plus with the other options.
-Fred-
Nate, An explanation of what Ecoating is and how it is done would be of interest to all of us I am sure. I personally have never heard of that process before and I am certainly up for learning something new.
-Fred-
These would be great for my November 1965 Kar.
-Fred-
I have an 8-62 housing if that helps.
-Fred-
Adison, I have a Shelby guy that may be interrsted in your trans. Please give me a call.
-Fred-
I have a 65 data plate decal that freshens up an original data plate. It is not the best but beats no background at all. I have had it for at least 25 years and I cannot at this time figure out where to get another one. I never had one for a 66 and am not sure that one was ever made.
-Fred-
Sounds great Dave!! It makes me wish that I had an old fashioned 65 that used the system rather than my ultra modern 66's.
-Fred-
You are absolutely correct Gene about the repro door tag.
-Fred-
Bob, I have received your email and responded with pictures.
-Fred-
Nike, I sent you both an email and a PM.
-Fred-
Bob, My emails to your jacsinc email addrsss have come back as failed. My phone number is in my PM. Either call me or leave me your number and I will call you.
-Fred-
From the pictures with the engine out, it would appear to have the correct 65 Hipo mounts at that time. The underside picture also seems to verify this.
-Fred-
I took my information from the Ford parts book and not Tonys book. I am at least glad that they agree. The Ford parts book also lists different jets for 5,000 to 10,000 feet and 10,000 to 15,000 feet. They basically go down 2 sizes on both primary and secondary for every 5,000 feet of altitude gain. The 44F primary jet size that you are listing is even too small for most standard 4V carbs below 5,000 feet and the secondaries do not start off that small for any 4V carb even above 15,000 feet. The 48F primary jets on the C6ZF-C are listed for 10,000 to 15,000 feet.
-Fred-
Tim, There is probably nothing wrong with your engine codes. The only reason that the Portland heads could not be Hipo heads is because they were stated as being an early 66 date code and having emission holes. The 66 model Hipo never had emission holes. Only standard 289's could have emission holes in 66. 67 was the first Hipo heads that could have emission holes and from what I understand, only 14 California cars were built that way and then only late in the production year. There are certainly early 66 date code Hipo heads but those in Portland cannot be Hipo heads. 66 Hipo heads will have 66 date codes however they will have a 65 casting number. Do not let that confuse you though as Ford did use the same castings for more than one year on these.
-Fred-
One of the better done Ebay auctions with the pictures during restoration.
-Fred-
The original C6ZF-F carb at 0-5,000 feet of altitude will have 50F in the primaries and 69F in the secondaries.
-Fred-