The first auction is for a mini spool rear end only. This would not be suitable for street driving.
-Fred-
The first auction is for a mini spool rear end only. This would not be suitable for street driving.
-Fred-
All of the intake gaskets are the same on 289 engines regardless of horsepower. The NOS C3AZ ones are $15 per side.
-Fred-
The Ford number is a C3AZ 9441 A for the side gaskets. These are the white asbestos gaskets that the Shelby guys really need for their cars as they can been seen after they are installed. I have quite a few of these in stock.
-Fred-
That one is not a Ford manufactured starter and Dan is looking for an original. The seller states the fact that it is not a Ford starter in the questions and answers at the bottom of the auction.
-Fred-
That unit that you linked with is a Trac-Lock if that is what you really need. Unless you are driving this Kar in slippery conditions, like snow, an open rear end is all that you will need. There is really no need to pay a premium for the locking rear end. Ford did not even offer a locking rear end for a 65 Hipo Kar. My only concern would be that your Kar will need a very specific and hard to find pinion yoke which the seller may not have. If you are not concerned with date codes on your castings, this may be right for you as all of the internal parts are new.
-Fred-
Gerry, your Kar should have 28 splines on the axles.
-Fred-
I have 3.00 gears in my Kar and I like it because I do a lot of freeway driving here in Los Angeles. This Kar has been like this since at least 1984. I have had 3.50 gears in most of the other Kars that I have had over the years and although they are great around town, I prefer highway gears for my use. I had a 64 K Fairlane with 3.89 and it was not that great on the freeway. I had a 65 K Fairlane that had 2.75 gears and it worked well for me. My Boss 429 has 3.91 and it too would be more useful to me with a taller gear but then I rarely get it out on any long trips. The taller gears make the Kars a little lazier getting away from a light but make all of the speed gears much longer winded. Keep in mind that all of this comes from a guy that had 4.88 gears in his new 67 Camaro that he put a 427 in just after he bought it new. I thought nothing of revving my engines at over 4K consistantly on my trips to Las Vegas and San Francisco at the time. I even ran 5.38 gears in my street 427 Vega panel truck. My 66 427 Corvette had 4.88 gears in it when I first bought it 29 years ago and it was useless for my canyon driving as I ended up in 4th gear most of the time. I now have 3.36 gears and it is far more useful. All that said, the 3.50 gears that Ford used as a standard ratio in K Mustangs works well around town but where I live I have a lot of freeway driving so a taller gear is my preference.
-Fred-
Welcome to the site, Mike. It is good that you were able to still have your first car at this point in your life when you appreciate it more.
-Fred-
This topic has been discussed here before. The link is below.
-Fred-
Rene, That piece that you are looking at is the tail light wiring protector. It is cardboard.
-Fred-
Very good research Dan.
-Fred-
Sounds great Dave! The hobby thanks you for all of your efforts in pulling this together.
-Fred-
I have been working on T10's for over 45 years now. Obviously in the beginning the ones that I worked on were GM transmissions as there was no Mustang at the time. They work well and are far easiler to work on then toploaders. Their drawback seems to be that the synchro teeth wear readily and it does not take as much wear as a toploader before the T10 starts popping out of gear on decelleration. This is usually a second and third gear issue. The sychros are readily available for replacement but the gears are tough to find and they are the biggest part of the problem for popping out of gear. I am not a fan of the gear ratios in the Mustang T10 versions especially the 66 version. The Shelby version has a good gear ratio but is cost prohibitive to run in anything other than a Shelby in todays market as the last Shelby T10 that I saw available was $6,000.
-Fred-
Merlyn, You might count the teeth on the second gear. If it has 28 teeth then it is a close ratio for sure.
-Fred-
I agree with Bo on the H64 date code on that fan.
-Fred-
Tim, The HEH-P is a 25 spline output wide ratio trans for a standard 289 Mustang. It is not for a Hipo. Your Kar will need an HEH-T which is a 28 spline output close ratio trans.
-Fred-
Charles, The reason that I like my method is that there is no thinking involved. After the intial setting on the first crank position, you will only be adjusting three or four valves per crank position as the others will be tight and will be obvious. This way there is no need to watch which valves are moving as it becomes unimportant to the process. I can actually run a valve adjustment this way in around ten to fifteen minutes on a Hipo 289 as long as I do not have to change valve cover gaskets.
-Fred-
Troy, In regards to cold or hot settings, that is up to you. The Ford camshafts list both a hot and cold setting. Not all camshaft manufactureres list both hot and cold settings.
-Fred-
I figured out this method a long time ago. I have been using this method for over 40 years with total success. It is not in any books or online anywhere except this posting. Some books list a process where the engine is at some predetermined point and you would adjust certain intake and exhaust valves at that time. This requires entirely too much thought and the book needs to be there to read while you are doing this. On top of that that method only works for the particular firing order of the engine you are working with. My method works on all cars with adjustable rocker arms. To begin with, of course, the valve covers need to be removed. I usually assume that any valves will be loose rather than tight. If there is any chance that they are too tight then you need to loosen them all a quarter of a turn for this process to work. Usually the only reason for them to get tight would be if the valve was sinking into the seat. This happens most often with exhaust valve seats that are not hardened for unleaded gas usage. You can start this process in any position of the engine. To make it simpler you can remove the distributor cap so that you can watch the rotor position. You now take a feeler gauge for the proper clearance and check all of the now loosened valves, you merely tighten the loose ones down to fit the gauge clearance. Do not loosen any others that are tight. Then turn the engine one quarter turn and repeat the same process and only adjust the loose ones. By the time you have done this eight times, you have run the camshaft through a complete cycle. Just reinstall the valve covers and distributor cap and you are done. This also works for hydraulic lifters. For hydraulic lifters you do not need the gauge. Just make sure that all of the valves are loose. If you are installing a new cam, changing heads, etc. you will be intalling the rockers for the first time so they will be loose. Tighten each rocker arm down while you are spinning the push rod with your fingers. As soon as you feel a slight tension on the push rod it is time to stop as you now have zero clearance. Do the same routine for the eight quarter turns on the crank and all of the valves will be at zero clearance. Then you tighten them the proper amount of turns specified for the camshaft that you are using.
-Fred-