I have already committed to these heads.
-Fred-
I have already committed to these heads.
-Fred-
There are no aftermarket "Y" pipes for Hipo manifolds in a Mustang as all Hipo Mustangs used an "H" pipe with dual exhausts. You will need a custom made setup.
-Fred-
The price has now been raised back up to $125,000.
-Fred-
First off, I do give credit to the seller for their pictures. I believe that they are probably unaware of what they really have. Besides the issues already addressed, this Kar has a few more issues. The door tag shows Axle code as H for a 3.89 locking rear end. You could not get a locking rear end in a Hipo in 1965. Rear end housing is a clone. For a newly restored Kar, the strut rod bushings are already cracked. My further comments are based on the "newly restored" statement which should have made it a better Kar. The convertible bolt-on floor pan tie plate is backwards. There is no rear end snubber. Should not have right side filler board in trunk. Poor fitting convertible top above doors. Perhaps it is missing the tie cables for this. 66 style lower clutch adjusting rod. Standard rather than Hipo Z bar. Appears to be standard rather than Hipo motor mounts. Unknown, possibly Granada, disc brakes. Wire loom coverings are all GM type. The heads are way too early for the production date. Gypo export brace, high profile Rally Pac rather than low profile, GM style Holley carb, Pertronix, C8ZE harmonic balancer, no choke cable, poorly fitted instrument panel speaker cover and no glove box door bumpers. The following are obviously incorrect:
Radiator
Thermostat housing
Hose clamps
Seat belts
Rear brake hose (does not appear to attach to body incorrect position either)
Orange plug wires
Ignition coil
As Charles says, a thorough inspection needs to be done on this Kar as I agree that the Hipo body, GT and pony interior are all questionable.
-Fred-
The changeover to the later 66 style housing, according to the Ford book, was on October 1, 1965. This was around the same time, November 1, 1965, that the motor mount assemblies also changed. I have a November 1, 1965 Kar that has the early style motor mount assemblies. Do I have the true last day of production for the early mounts? Does anyone have a later production date Kar with the early style mounts?
-Fred-
Lyle, If you have a Ford parts book, part numbers would make your search much easier. If you do not have a parts book, I do, and I can look up the information. Just contact me off site for help.
-Fred-
There are plenty of people on this forum that can use it, especially since I can now get them rebuilt.
-Fred-
I just sent you a PM.
-Fred-
Great looking rides!!!
-Fred-
Here is the sellers latest additional comment on this auction:
On May-01-08 at 16:24:43 PDT, seller added the following information:
Note: For the purist, we can't account for what the Factory did when producing cars, but the numbers on the carb designate a 1963 Fairlane 390 V8 car carb. I can tell you for sure it came off a untouched 65 Mustang HiPo 289. Tacking ventury and meter measurements I figure this carb to be approximitely 500CFM. Ford did several things during production and actually different plants did builds on the same model differently. Hope this helps with any questions. We thank you for the interest and want you to be totally satisfied
-Fred-
Charles, Your description sure matches the fiberglass ones. When I first realized that the part number was still many available years ago, I was excited to be able to order them. That exctiement faded when I received them.
-Fred-
Charles, I have NOS plenums in the Ford box with part number C5ZZ 18471 A. Many years ago when I first got them from Ford they were actually fiberglass pieces. The fiberglass is very crude and I had a dozen of them at one time. Are these the ones that you are calling tar coated? I believe I still have one of the fiberglass ones just for posterity. Ford in later years serviced the same part number but this time it was a hard plastic of some sort and actually are a very nice piece with a Ford logo and engineering number cast into it. It would have been a batter part if Ford had used them in the building of the cars in the first place. I still have a few of them in stock, also for posterity.
-Fred-
Gerry, According to the Ford parts book you will need a C2DZ 17271 G which has 17 teeth. You should have a 20 tooth gear at present with your 4.11 gears. If you need one, you can contact me as I do have one.
-Fred-
This carb is listed on Ebay as a 65 Hipo carb.
http://cgi.ebay.com/ebaymotors/65-…sspagenameZWDVW
I questioned the seller about it as quoted below.
Hi,
Just trying to help you out here. This carb was originally for a 63 full size Ford with a 390 and Cruiseomatic transmission. A 65 Mustang Hipo, although with the same 1.12 venturi size, was a manual and not an automatic choke. The body of the carburetor for a manual choke is different than an automatic choke carb and only the 65-67 Hipo 289 engines had manual choke 4V carbs. If you need more help please feel free to contact me. I can email you a picture of the proper carb if that would help.
Good luck,
Here is the sellers response to me.
Well thanks Fred but here's an anomoly, This car is in house untouched, one owner. Bought in Maryland, Dec 14th 1965, We have build sheet, Window sticker. and bill of sale. Ford tech sheet also. Guess what this car is Virgin and had this carb. Only at Ford
Does this explanation work for anyone else on this forum? If this Kar is so virgin, why would you sell the original carburetor? This sure does not work for me.
-Fred-
The short block does appear to be a 67 Hipo one. I cannot see the part of the rear counterweight that I need to verify the crank. It would not surprise me to find a VIN on the block. It would be good to find out the numbers on the harmonic balancer.
-Fred-
From the description in the auction the seller is clearly representing this as a Shelby and not a Hipo Mustang. His statement that this car left the Torrance plant on May 16, 1966 is only true for the Shelby ID tag as most everything else Shelby appears to be non existant on this car. It does not even have the correct export brace. The seller now states that the gear box is not an alloy one as was first stated in the auction. Being that the original car was a Hertz model, it would have had an aluminum alloy trans but it would have been a three speed with a torque converter and not a 4 speed with a clutch. My take on this after reading the auction a number of times is that this car is originally a Hipo fastback with a pony interior as all of that looks correct. From the placement of switches on the dash it may have been a GT as well. Being as the seller is having a hard time reading the Ford VIN, it is clear to me that it is titled as a Shelby and not a Mustang. This is no different than taking a "K" VIN and title and putting it on a 6 cylinder car and calling it a Hipo. All of this represents fraud to me. There is at least one person on this site that has been a victim of this type of fraud.
-Fred-
What did Cobra Automotive quote for the drums? Are they NOS Ford or aftermarket ones?
-Fred-
Are you measuring drum size or brake size? If you are measuring brake size, you have GT350 brakes and that is why they are so expensive. There are no longer any aftermarket drums suppliers for that size. If that is what you need, I can still come up with some new aftermarket rear drums for 10 X 2 1/2 inch brakes. Drum sizes are generally 1/4 inch wider on the surface than the brake shoes that they are used with.
-Fred-
Dave, See my post under C4 flexplate.
-Fred-
Balancing a flex plate can be done by a qualified shop however, the total engine balance will be in jeapordy unless it is all done together. Engine balancing, when done properly, has everything weighed in grams. The only hope that you have for a correct copy of the balance on the flex plate is if you had one that was already balanced to your engine. Of course, then you would not be needing another one. If the engine was balanced as a stick shift previously, the flywheel can be used as a match to get the balance pretty close.
-Fred-