I just received a reply from the seller to a question I had about this carburetor. He states that this is a tribute carburetor so if any of you have bid on this, you have been warned.
http://cgi.ebay.com/ebaymotors/ws/…em=300225301754
-Fred
I just received a reply from the seller to a question I had about this carburetor. He states that this is a tribute carburetor so if any of you have bid on this, you have been warned.
http://cgi.ebay.com/ebaymotors/ws/…em=300225301754
-Fred
This car is now back on Ebay again as a Buy-It-Now.
http://cgi.ebay.com/ebaymotors/ws/…atchlink:top:us
-Fred-
Jim, The Ford cross reference book is not reproduced and there have been quite a few of them over the years. They are available to Ford dealers on microfiche as well as books. There are still three Ford cross reference books related to parts in the era of our interest that are still available. The FPS 7425-2 volume 2 covers from September 1959 to April 1966. The FPS 7425-4 volume 4 covers April 1971 to April 1975. The FPS 7425-5 volume 5 covers April 1975 to April 1980. I mention the last two volumes because they sometimes have some of the older numbers in them. Volume 3, which you will really need, is not available as a book but is available as a microfiche. I do have the volume 3 books myself. The Ford dealer cost is $50 each. The dealer can also order two microfiche of the same information for $85 each Ford dealer cost. They would be FPS-7425-M2-4 which covers volume 2, 3 and 4 of the books. The FPS-7425-M5-7 covers volumes 5, 6 and 7 of the books. Any Ford or Lincoln-Mercury dealer parts department can order these for you. If they do not know how to look them up you can contact me. I would expect that the dealer would mark these prices up.
-Fred-
The information that you were given on GT "K" codes for 1966 is in error. A "K" code car was not a GT by default. There are plenty of non GT Hipo Kars that people own on this site alone. The only way that you could get the GT package in 1966 was with an "A" or "K" engine. I believe that is where the confusion lies for your local parts guy. He just has it backwards.
-Fred-
Fred is not upset as he can handle this one easily. Sorry, Jim.
Sometimes it helps to have the Ford cross reference books. They do not always work out but they did on this one. The C7ZA 7541 D is the engineering number that cross references to a C7ZZ 7515 C Ford part number. This fits 67 and 68 Mustang 200 inch 6 cylinders with a 3.03 trans (except H.D. clutch) from 11/21/66 to 2/15/68. The correct one for the 67 Hipo 289 is the same as the one for a 67 and 68 Mustang and Fairlane with a 390 if that helps. That one will have an engineering number of C7ZA 7541 E and a Ford part number of C7ZZ 7515 D.
-Fred-
Great story and timing, Gerry. I wish you the best on this deal.
-Fred-
Those valve covers are the real deal.
-Fred-
I have sent you both an email and a PM on this.
-Fred-
That sure sounds right to me.
-Fred-
Using the registry as a guide, this car was produced near the end of February 65. Is that still too early to be a GT or pony interior car?
-Fred-
The bolts for the spring covers should not be painted.
-Fred-
Very nice work, Dave.
-Fred-
Yes, these are very wavy in the casting but I was more noticing the difference in the lettering. As far as spark plug socket clearance, I have had problems on the right side manifolds with originals. I found that I would install them by just letting them hang on the bolts to the head before tightening them. This caused some of the casting flash to be too close for the spark plug socket. I figured out that by holding the manifold in its highest position on the head while tightening the bolts, solved the problem. This may work with reproduction ones as well.
-Fred-
Congratulations Dave on your 1,000th post.
-Fred-
Joe, The only difference in the Fairlane manifolds is on the right hand side for 63 and 64 Fairlanes as the manifolds are setup for a fitting for the automatic choke. The exhaust pipe area is the same so a Mustang "H" pipe will also fit the Fairlane manifolds. The Fairlane used a different "H" pipe for the Fairlane body.
-Fred-
http://cgi.ebay.com/ebaymotors/289…sspagenameZWDVW
These are different than any other reproduction Hipo exhaust manifolds that I have seen. Note the lettering style and angle.
-Fred-
Jeff, The Ford book I use is the 1965-1970 Ford MPC which has not been updated since 1970. The books most people have are the final printing issue from 1975 that covers 1965-1972 cars. The reason that I like my non updated version is that it has all of the older numbers before they were replaced or obsoleted. The rear end housing is not in the later book version however the motor mounts are. I agree that scheduled build dates are not that accurate and I only put this out as a research question for our forum. I will also state that the Ford MPC is not Gospel, but fairly close on most things.
-Fred-
This Kar has now been removed from Ebay by the seller. The last high bid was $26.666.01.
-Fred-
Mike, Yes, I have been working with him on these heads for a couple of weeks. His wife put them on Craigs list without his knowledge. I just spoke with him and he has now removed them from Craigs list.
-Fred-