Jeff Speegle is far more at risk on a daily basis as a firefighter than any of us will be in driving our old, unsafe by current standards, Mustangs. I even ran with scissors when I was a kid.
-Fred-
Jeff Speegle is far more at risk on a daily basis as a firefighter than any of us will be in driving our old, unsafe by current standards, Mustangs. I even ran with scissors when I was a kid.
-Fred-
The trans VIN will be stamped front to rear near the bottom of the main trans case. A San Jose car has the VIN from stamped side to side on the tab where the tailhousing meets the main case at the bottom. Here is a link that shows some examples.
http://www.hipomustang.com/hpmx/topic.asp…Terms=trans,vin
The answers to your ALL your questions (and then some) are contained in the Fourth Edition of The 289 High Performance Mustang, which is available directly from this website. Your purchase will also help keep this website going.
http://www.hipomustang.com/default2.asp?page=13
-Fred-
Good eye on the ignition switch. I just expected it to be installed in the dash.
-Fred-
You should have a VIN stamped on the right side front of the engine block above the oil pan rail. You should also have a VIN stamped on the trans.
-Fred-
It look like a good idea however the fuel filler pipe hose could still be torn loose.
-Fred-
Cool ride Merlyn.
-Fred-
You are correct as it is quite a bit past known production VIN's.
-Fred-
There is no mention of the trans or rear end and with all of the other changes, these would be suspect as well. The pony interior seat covers appear to have been installed over the original standard interior foam rather than pony foam. I do not see any K parts on the engine with the possible exception of the fan as it appears to be correct. The car is obviously not a GT.
-Fred-
I am surprised that the automatic choke mounting holes were not filled in better as Pony carbs does a good job of that.
-Fred-
Quentin, the number that you have here is a casting number which is fairly generic. You need a stamping number from the mounting flange that ends in an S to get a read on what this actually fits.
-Fred-
The numbers that Hilo 38 posted are incomplete as RPM pointed out. The numbers are actually C5ZZ 6028 A and C5ZZ 6029 A. However these part numbers can not really be mistaken for any others as there was never any other suffix used with these numbers for any other application. These parts have no engineering numbers on them and are somewhat crudely made pieces.
-Fred-
The "C" pulleys were stamped in a straight line and not curved like the "H" pulleys.
-Fred-
Thank you Charles for the confidence in thinking that I might know when the production changed on these. I really do not but I will try to research it.
-Fred-
Being so close to the "official" cutoff date for the alternator pulley, I would say it is probably correct.
The carb will be stamped on the left front toe of the carb on the side. A picture from the top side of the choke linkage where it mounts to the carb body would help to verify if it is real or a clone.
The intake casting is on the runner in front of the carburetor. It is not subtle. I see it in one of your pictures and it appears to be a C5AE 9425 M.
The reinforcements for the exhaust are spot welded and look correct. They are on Hipos as well as GT's in your production time.
Rally Pacs were optional equipment and were also available over the parts counter. The Rally Pac is the tach and clock cluster that clamps to the steering column. I only point this out because you are mentioning the 5 dial instrument cluster and you might be confusing this with a Rally Pac.
Where is your fog light switch as it should be under the dash in the "D" shaped hole near the choke cable?
You have a reproduction data plate and a later model 66 rear end housing.
-Fred-
Make sure that the one that lines up with the distributor is tapped and seated far enough in to clear the distributor. You can probably guess how I found that one out!!
-Fred-
The actual term that the seller of the radio delete plate used is "like NOS" which can easily be confused for NOS which is what the seller hopes to imply.
-Fred-
Great way to show your colors!!
-Fred-
Craig, these rebuilds are back to whatever you send in as a core. There are no immediate plans to make upgrades to dual springs as I am unsure of the availability of the necessary parts for the conversion.
-Fred-
Chris, you are a man that goes for the gusto!!
-Fred-
The right side is actually just a vent assembly with the same door as on the heater box. It looks like a tube, the same size as the heater inlet, with a 90 degree bend and the vent door facing the passenger.
-Fred-