This is its fourth time on Ebay and the highest offer was only $17,000 and that was only on the first auction. The seller really needs to address the lack of information issue.
-Fred-
This is its fourth time on Ebay and the highest offer was only $17,000 and that was only on the first auction. The seller really needs to address the lack of information issue.
-Fred-
This is their second time around on Ebay. I would certainly want the rear one as well although they do not offer it. I am unable to ascertain if the metallurgy of these caps is up to Ford standards.
-Fred-
Well done Joe!!!
-Fred-
A Boss 302 and a HP 289 use the same rod length. Standard 289 rods are the same length as well. A standard 302 rod is shorter to compensate for the stroke difference from a 289 as the 289 and 302 use the same pistons. Does this help add to your confusion?
-Fred-
Dan, I have a limited supply of Hipo distributors to check for date codes. I do have a FoMoCo 6AA so the that dating system did last at least until then. I do not have any standard distributors to check to see if the dating system changed past that date but there are plenty of them around that other people might have to check.
-Fred-
From what I have seen, Ford also stamped the engine assembly date on the right rear of oil pan rail to match the date on the pad in front of the head.
-Fred-
This Kar is not as originally built. It was not a GT, did not have pony interior and was not this outside or interior color. It did have an 8 inch rear end in it at one time and I am unclear as to whether the rest of the drive train is original. Other than that, it is all original. ![]()
-Fred-
My original on one of my Kars is fairly rough so I keep it with the Kars title in the safe. I have an earlier repro on the Kar which is not as nice as the Marti ones.
-Fred-
Dan, I replied to your email letting you know that I have the distributor that you need.
-Fred-
Dan, give me a call as I have a 4HB. There never was a number 8 at the end of the date code.
-Fred-
The NOS Ford cables that I have had did have the foam.
-Fred-
Dave, send me an email so that I can give you my phone number to discuss this.
-Fred-
Some of your numbers need some work but this will help you some:
C5DA-6394-A bellhousing
This is correct for all 65/66 Mustang 289's whether standard or Hipo.
C0ZE-6380-A fly wheel
This is probably a C6ZE and is not for a Hipo.
C3O6-6380-B Fly wheel
This will be a C3OE and may or may not be for a Hipo depending on the balancing and Brinnell test mark.
C4ZA-6CO41-B Motor mount
This is for a Hipo.
C4ZA-6AO30-B Motor mount
This is for a Hipo.
C3DA-6AO3O-B Motor mount
This is for a standard 289.
C3DA-6CO41-B Motor mount
This is for a standard 289.
C3DA-8CO41-B ? about the 8
This will be a 6C041 and is for a standard 289.
-Fred-
You need a type 3A but specifically it needs to be a left hand helix. I have them in stock if you need them.
-Fred-
I have an NOS Ford drag link but it has a zerk fitting.
-Fred-
A friend of mine had a 66 Hipo fastback with the same "T" code on the fender apron. It was definitely a Ford error as everything else checked out. It was long enough ago that I do not remember more details but I can ask him as he possibly will remember.
-Fred-
The Hipo and standard 289 Mustangs use the smaller C5DA 9384 A casting number aluminum bellhousing. This is for the 157 or 160 tooth flywheel. The reason that I mention both 157 and 160 tooth flywheels is that the flywheels are the same and the 160 tooth is original. In later years Ford changed to a 157 tooth ring gear as it meshed better with the starter than the 160 tooth version. Ford replacement ring gears were 157 tooth as well. The C5AA 6394 A casting number aluminum bellhousing is used on 65 Hipo and standard 289 Failanes and other Ford car applications with 164 tooth flywheels.
-Fred-
The thickness is about .308 compared to about .210 for the standard ones.
-Fred-
White smoke is generally steam which indicates water in your engine somewhere. However it is more likely to be condensation in the exhaust system if it goes away quickly.
-Fred-
I have a fuel pump here for rebuilding that belongs to Paul Calvesi. I have no contact information for him. If Paul or someone who knows him reads this, please have Paul contact me.
-Fred-