Posts by C6ZZKGT
-
-
Brock, I sent you a PM being as the email system is broken.
-Fred-
-
Matt, In regards to the carburetor, is this a 4 speed or automatic trans Kar?
-Fred-
-
This car is listed as a K code however I have some doubts. The door tag information in the ad does not mention the VIN but gives all of the rest of the codes. It is listed as having factory disc brakes however they appear to be Granada ones as the calipers are at the rear rather than the front. It has no parking brake setup. It also has an eight inch rear end. The pictures are not quite good enough for me to tell if the snubber plate is correct although it does appear to have exhaust hanger holes in the right frame rail above the axle. That would be for a transverse single exhaust muffler which, of course, would be wrong. I cannot tell where the rear brake line mounts on the body and I do not see any of the dual muffler hanger setup on the panel under the seat. The bellhousing is incorrect as well. If a moderator wants to pull this post down due to the sketchy nature of the K code status, I will not be offended.
http://cgi.ebay.com/ebaymotors/ws/…em=250310145500
-Fred-
-
The 76B body style makes it a luxury interior convertible. Back when they were new a convertible was not the hot tip for racing being as they were heavier. If you were a hot rodder back then you would buy the cheapest coupe for a Hipo drivetrain. A luxury interior convertible was way down the list for a hot rodder wanting a Hipo drivetrain so few were built. 40 years later they have become highly desireable due to their rarity. The big three on these are Hipo, GT and luxury (pony) interior. I have had 3 of that configuration myself. Rarity and desireabilty tend to drive the prices up. If it is unrestored, in good condition and with low mileage, this can be a gem in the rough. You need to be prepared to spend more than you might think for the purchase and a whole lot more to restore it.
-Fred-
-
-
Does the cannister that you bought from New England Mustang have the double row of ribbing on the bottom or is it a hex or three indentations?
-Fred-
-
The downside for people from Australia right now is that their dollar is well below ours at this time. They were far closer to our value six months ago. The last that I heard was about $.65 to $.70 to our dollar.
-Fred-
-
The 65 Shelby one is a Shelby unique piece that has a higher center peak to it and, I believe, is aluminum rather than pot metal like the C6ZZ 8221 A.
-Fred-
-
These mounts are going on one of my early production 66 Kars.
-Fred-
-
The C6ZZ 8221 A although similar to the Shelby piece is not the same and is for 66 Mustangs only.
-Fred-
-
-
Emails sent from this site are not getting through so the PM system seems to be the only way at this time. I experimented with sending emails to Gene today while we were talking on the phone and the email system did not work. There does not seem to be a solution to this problem at this time.
-Fred-
-
I have several Hipo transmissions and most of the Dearborn ones have the VIN out in the open like this trans. On the San Jose ones that I have, the VIN is on the lower tab like the ine that RPM has. The ones that are stamped on the tab appear to be freehand as they are quite irregular. The Dearborn ones are mostly pretty straight although some are not. It appears to me that trans and engine stamping may have been done after the assembly was already in the Kar as they are in the right position for this. The 68 and up VIN stamps on all engines and transmissions as required by the Feds were obviously done before installation as they are in areas that cannot be reached once installed. It generally takes a mirror on them to read the numbers.
-Fred-
-
The car has a later model rear end snubber and I do not see a fill plug on the rear end housing although the plug may be there. I do see a fill plug on the third member which makes it a later model than the car. It has a replacement fuel pump. The dash paint around the radio is very rough.
-Fred-
-
I did not go over the ad for this car thoroughly. Just one item that caught my eye right away is the carb with the following quote from their ad:
"It is correctly date coded and even has the proper tag on it as does the engine. This carb was rebuilt and detailed by Pony Cars. These Hi-Po carbs are rare and very expensive and it is a big plus to have one. As a result, of this Mustang being such a significant car a professional restoration was performed on it."
The problem for me is that this rare, expensive and correctly date coded carb is a CLONE! It is not a Hipo carb at all. That does not get me off to a good beginning for my trying to believe other statements in the ad.
-Fred-
-
Great looking perch!!
-Fred-
-
These last mounts do not have the welded together steel plates that mount the rest of the mount to the cast iron frame bracket.
-Fred-
-
I have sent you both an email and a PM.
-Fred-
-
The six in the VIN is definitely a six and not an eight. You just have to slightly magnify it to see this for sure. If you do not have a virtual maginifying glass on your computer, I have attached a link below. I have been using it for many years and it works great.
http://magnifier.sourceforge.net/
-Fred-