Posts by C6ZZKGT
-
-
Judging by the VIN, this is actually a 65 and the seller is listing it as a 64 1/2.
-Fred-
-
Well, I guess that being that this is a KGTA we can rule out the 4 speed.
-Fred-
-
Bob, I thought about the dimple in the arm while I was going through the rebuilding process. It is fairly deep and I feel that the arm would need to be heated rosy red there to accomplish the task of stamping the dimple. I was afraid of hurting the heat treat of the arm. A spring is certainly not a big deal to come up with. I have an NOS C5OZ spring and it is red. The bottom line for me on the second spring is that the service we are usually putting our Hipos through these days (lower RPMs than red line) would not need the second spring. If I was going racing with a Hipo these days I would elect to use a less valuable pump.
-Fred-
-
Welcome to the forum, John. We would love to see pictures of your Kar.
-Fred-
-
Rene, that sounds like a great idea to me.
-Fred-
-
This must have been the first replacement type C8ZE balancer. It appears to have a C8 date code. Maybe Bob Mannel can shed some light on this one.
-Fred-
-
-
For all of you who have prepaid your pumps, I packed quite a few of them today and already managed to get some of them off to FedEx. For those of you who are not paid I have already contacted all of you by email. If you did not get an email from me, you need to contact me as I have had intermittent email problems.
-Fred-
-
Check with a local glass shop for the proper sealer. I use what they call windshield bedding compound. Do not use silicone. The windshields are tough to seal at best.
-Fred-
-
Welcome to the forum, Walter
-Fred-
-
RPM is another person on this site. Bob Mannel is on this site as bobmannel.
-Fred-
-
Very sharp eye Darrell as this reference must have been tough to find.
-Fred-
-
Rene, I only put the link up to show that the Kar has previous history on the forum.
-Fred-
-
This Kar has been discussed here before.
http://www.hipomustang.com/hpmx/topic.asp…e&TOPIC_ID=2066
http://www.hipomustang.com/hpmx/topic.asp…e&TOPIC_ID=3736
-Fred-
-
The undercarriage does show its rust history to some extent. It does, at least, have the correct motor mounts which are frequently missing.
-Fred-
-
This Kar has been discussed here before.
http://www.hipomustang.com/hpmx/topic.asp…ue&TOPIC_ID=683
-Fred-
-
This picture probably represents the largest gathering of this style of fuel pump in recent history and probably for the future. I appreciate everyones trust in sending me your "babies". I put forth my best efforts to make these come out as good as possible with all of the challenges that took place. I took this project on as a challenge and I am happy that I was able to see it through. This involved a number of trips to the rebuilder and plater. I had to engrave ID's, disassemble the levers from the pumps and do my own cleaning on these. The reason that I had to disasseble and reassemble the arms was that the rebuilders typically drill out the opposite side of the casting to remove the pin for the arm. They then fill the hole in when they reassemble them. There was one on Ebay yesterday from GGT500 that was done this way.
http://cgi.ebay.com/ebaymotors/ws/…%3AIT&viewitem=
I did not feel that anyone on this board would want their pump done this way so I had to figure out and make some tools to remove the pin without drilling out the casting as the rebuilder would have done. This, of course, took a lot more time than the way the rebuilder does it but I felt that it was mandatory. Had I not given the rebuilder some samples of mine to do I would not have known about this until it was too late. Then when it came time for reassembly, they really did not want to do them one at a time to keep everyones pieces together as they usually run an assembly line to make things easier for them. One thing that overcomes this kind of problem is money so I renegotiated the price to make sure that they were done properly. In the end everyone will get back the exact pieces that were sent to me minus some dirt and plus a rebuild. I give credit to Bob Peckham for his input on how to ID the pieces to keep them together through all of these processes.
-Fred-
-
Charles, Just for the record there are ten 3939-S pumps and eleven 4201-S pumps in this batch.
-Fred-
-
Gene, Yours is actually the first one in the second row. The one that you thought was yours actually belongs to Bob Gaines.
My thanks go out to Britton for posting my picture.
-Fred-