Posts by C6ZZKGT

    Shelby came up with a lower pulley that fit inside the original single groove pulley to run the A/C belt. The factory A/C pulley was only a 3 groove and the outer part sleeve made it too large in diameter. By coming up with a pulley that fit internally, the problem was solved. A friend of mine has one of those pulleys and it is aluminum and looks strange because it is so deep. It appears to me like the pulley was from some aftermarket A/C system that was available at the time. It is pretty crudely finished.


    -Fred-

    I have run into this problem before myself. I have found that loosening the manifold and lifting it up and then retightening it works the best. The problem begins when somebody puts the manifolds on and just lets them hang from the bolts when they tighten them. I let them hang all of the time on other engines and the Hipos are the only ones that I have experienced this problem with.


    -Fred-

    A/C is always a talking point on this forum as Hipos originally did not come with A/C. I have put A/C in a number of Hipo cars and a lot of them were mine. The A/C that I use is always the Ford system that would have been factory installed in any given year. In 1965 and 1966 dealer and factory installed systems are the same. The one in the ex-Nelson car is a proper Ford unit. The problem with putting A/C in a Hipo is that if you have the original C5OE balancer, the lower A/C pulley will not fit as the minor diameter of the opening is too small. I have had to slightly enlarge the opening to make the pulley fit a C5OE balancer. If you have a C8ZE replacement balancer then everything fits fine. As far as value, keep in mind that Shelby installed A/C on all of the six 1966 GT350 convertibles that he built. Somehow I do not believe that it reduced the value of those cars.


    -Fred-

    There actually were no 6 bolt bell housings from Ford with both trans bolt patterns. There are at least one cast iron bell housing that has the material in place where you can drill and tap the narrow bolt pattern that you need. I have one and it is as if Ford planned ahead for both patterns but only drilled and tapped the wide pattern.


    -Fred-

    Lot number 1061, 66 KGT conv, was only listed in the results as being a Mustang GT Convertible. I was unaware the "K" status until I opened the link. If other buyers only went by the description they may have not noticed the Kar and therefore did not bid on it. Even though it was an automatic, it was still a better Kar in my eyes that the ex-Nelson Kar and should have brought much better money. Of course this is based only on seeing the Kar in the pictures and reading the description. A closer inspection might have changed that opinion. Did any one here see the Kar?


    -Fred-

    You are correct that it does not have an oil slinger. That is not really a factor for the chain to fit though as the slinger will only push the balancer slightly further out. The slinger is so thin that the difference would be minimal and not affect belt alignment.


    -Fred-

    It is a plain black wire with some printing on it and it does not plug into the triple plug that is near the radio. It follows the main wire loom over the top of the instrument cluster and clips into the large plastic wire loom retainers. It plugs in near the left air vent area.


    -Fred-

    Compared to the earlier auction, this Kar is missing even more Hipo components. There were not many to begin with anyway. About the only thing left now is the rear end and I am surprised that it is still there.


    -Fred-

    What is the problem with a 28 oz. offset on the balancer? To my knowledge, that is correct for a Hipo 289. I just rechecked that specification with Valley Head Service who did most of the hot rod head work for Shelby back in the day.


    -Fred-

    A friend of mine supplied the original balancer off of his Hertz Shelby for the manufacturer to repro these. I have one in my hands now and I compared it to an original C5OE. Except for not have the C5OE number stamped on the center hub and a date code next to the timing marks, it is really correct. He is willing to let me sell them to the people on this forum for $250.


    -Fred-