Posts by C6ZZKGT
-
-
On this particular Kar, it had all of the right options for what I look for in a Mustang converible. It is a Hipo, GT and pony interior. Those three together are really tough. Ford did not sell a lot of Hipo convertibles because most people that bought Hipos back in the day were interested in racing them. The convertible is the heaviest model and therefore the least desirable to race. If you were racing you did not need to spend extra money for GT and pony interior options and therefore the three together makes them especially rare today. Finding them in any condition is tough. This particular one also has a more desirable color combination as well. If I did not already have so many projects already, I would have stepped up on this one myself. Sometimes looking for this exact same Kar as a done car is just not possible as there were too few made and far less surviving until now.
-Fred-
-
My biggest problem with the Ford replacement caps is that they tend to separate the backing from the main cap as soon as you start to tighten the screws. At least the repro ones are held together with rivets rather than swedged over pot metal like the Ford ones. I have had some luck with using epoxy to help bond the backing with the cap. The screws from Ford come with a fair sized washer however Daves idea of a larger washer is also an improvement. I have about 10 NOS sets of these in stock myself so I probably can keep my two Kars going for a while.
I actually do have far more than I need.-Fred-
-
This Kar sold on Ebay on March 8 for $15,532.
-Fred-
-
Sold March 7 on Ebay for $19,900.
-Fred-
-
Sold on March 7 for $12,100.
-Fred-
-
An HEH-BT is a wide ratio trans. I know that flys in the face of the information on the toploader sites but their information on that one is incorrect. My information comes right out of the Ford parts book and this has been discussed here on this forum before. You need an HEH-BX to be correct for your Kar. If you are unable to find a trade, a friend of mine may have an HEH-BX available outright.
-Fred-
-
You really need to have the appraisal done where the car is to have any validity.
-Fred-
-
I may have a spare on my 66. I know that I have both 65 and 66 rims on it. I will check when I get home in the morning. I have sent you a PM with my contact information.
-Fred-
-
To further explain the Boss 302 and Hipo 289 connection I will add the following information. The 289 and 302 have a different stroke. Ford decided to use the same pistons for both rather than changing the pistons for the standard 302. This made a shorter rod the answer to keep the piston where it belonged for a standard 302. The Boss 302 went the conventional way of changing the pistons being that they needed a different dome anyway. By moving the piston pin hole closer to the top of the piston they can accomodate the longer rod like the 289 has. This is actually better as it cuts down on the critical angles that the rod attains to the piston throughout the stroke putting less stress on the skirts. This also gives more horsepower. The Boss 302 used 3/8 rod bolts and the same forging as the 289. Ford replaced the 289 Hipo rod with the Boss 302 rod around 1969 as a service part. As Dunc stated, the real difference is in the finish of the upper part of the rod where the bolt seats as the bolt heads differ in shape.
-Fred-
-
Chris, I just sent you a PM with my contact information. I have an extra standard Boss 302 rod to complete your set.
-Fred-
-
Chuck, In my opinion that would just be too early for anything other than maybe a first production 64 1/2 Kars. In my eyes it would even be too early for those as Ford used this casting in so many cars that they were constantly being produced and used just like standard engine blocks and heads. I would put date codes for rear end castings in the same time frame category as we put blocks and heads with scheduled production dates of the cars.
-Fred-
-
Mike, I sent you my email address in a PM so that communication will be easier.
-Fred-
-
Back on Ebay again with an even lower Buy-It-Now:
http://cgi.ebay.com/ebaymotors/ws/…3AVRI&viewitem=
-Fred-
-
Jim, All of them have the step down out towards the bearing end. You should do an advanced search through the forum as there are a lot of posts and pictures on this topic. One of the main things to watch out for are made up housings using 8 inch axle tubes. There is a noticeable step up from the axle tube to the center section where they weld to the center section whereas the proper housing has no step at all.
-Fred-
-
Mark, A build sheet is sometimes taped and wrapped around the main wire loom behind the instrument cluster.
-Fred-
-
Michael, If you decide to go with a standard steering wheel, I have the correct T-5 horn ring. I also have T-5 replacement inserts for your T-5 emblems if yours are worn looking. If you do not have your T-5 emblems at all, I am pretty sure that I have them as well.
-Fred-
-
Bob, Your 66 grille is the same for a GT and a non GT.
-Fred-
-
To the best of our knowledge, Ford did not ship T5's with gas caps but rather a plastic plug to fill the hole. The 65 with the Mustang word machined out has only been seen in reproduction form as far as I know. Pro Products made them up a long time ago but as yet I have not heard of an original one. I am certainly open to correction on this. A lot of the T5's got locking gas caps because they did not say Mustang. I also understand that you could purchase a Mustang gas cap and install it after delivery because then it was no longer Ford infringing on the trademark. The cap that I had on the Kar was an original normal Mustang GT cap that I had the outer ring, where the Mustang word is, machined down to eliminate the lettering for Ford Mustang. I then had it rechromed. I never intended this to represent what Ford actually did but only what I thought that they should have done. I felt that this went along with the Fairlane and Ford horn cap casting for the wood grain wheel that did not have the Ford Mustang wording. The center caps on the styled steel wheels in 66 were Fairlane as well.
-Fred-
-
Actually the original finish on the emblems is not totally shiny. You are correct that not much holds the badges on. I have the barrel nuts in stock. If you need new emblems, NOS Ford ones come with the retainer barrel nuts as well. I also have those if you need them.
-Fred-