Pro Products used to service the metal backed kits and they were nice. Unfortunately Pro Products is no longer with us.
-Fred-
Pro Products used to service the metal backed kits and they were nice. Unfortunately Pro Products is no longer with us.
-Fred-
Robert, You are making a good move by using an NOS one as the repros do not fit well.
-Fred-
That was one of the manifolds used at that time.
-Fred-
Ken, I sent you an email to what is apparently your old email address and it bounced. You still have a PM.
-Fred-
Tom, I do not see where the late 65 and all of 66 style mounts would be stronger. In the way the 65 and early 66 Hipo mounts are built, I feel that it is pretty indistructible. I see no way to break the rubber apart like you can on the later style mounts. The standard 65 and early 66 mounts are definitely weaker as there is nothing to keep the rubber from seperating. Is it possible that you are referring to the standard 65 and early 66 mounts?
-Fred-
This sold on Ebay with a best offer of $6,000.
-Fred-
The Amp gauge or Amp gauge wiring will have no affect on your other gauges as it is a stand alone gauge.
-Fred-
Mark, I measured an NOS Ford SS wheel and measuring from a straight edge across the back of the wheel to around the flat area on the front where the lug nut attaches, I have a variance of .540 to .600. The studs in my original rotor stick out 1.050 from the mounting surface. Your studs are the problem. Look at the photo posted above of the original wheel and rotor with the lug nut off. That is how mine looks as well.
-Fred-
Ken, I just sent you an email and a PM.
Bob, I just sent you an email.
-Fred-
Mark, I am sure that you will understand that I am not going to take a stud out of one my running Kars to check overall length. I did however knock one out of a good used original rotor that I have and it matches the Ford spec of 1.94 inches. This is measured from the end of the thread to the inside of the bottom shoulder. It actually measures 2.150 overall.
-Fred-
Front and rear part numbers on studs are not the same as the disc brake studs are longer. They have a longer shoulder where they press through the rotor due to the fact that the rotor is thicker than a drum. The front stud part number is a C5SZ 1107 A and the rear is an A9AZ 1107 B. I just checked one of my Kars for stud length and it has a full 1/2 inch sticking out past the wheel. This is at the outside of the wheel surface past the taper so there is even a little more of the lut nut below the taper. The Kar has original Ford rotors and SS wheels.
-Fred-
Chuck, I received your email and phone call. We will talk when you return home after Easter.
-Fred-
Randy, I am unaware of any repro 67 specific Hipo exhaust manifolds. The originals had C7ZE numbers for 67 only and Ford serviced them as replacement parts for 65 and 66 Hipos under Ford part numbers C3OZ 9431 B and C5ZZ 9430 B. I had some in the original Ford boxes with those part numbers. The manifolds were dated late 67 after the cars were no longer produced. The 67 manifolds only differ in a relief machined into one upper corner of each port where they bolt to the head. This is for the thermactor tubes when they are used. I have had problems with casting flash on original 65 and 66 manifolds getting in the way of a spark plug socket at times. All that needs to be done is to loosen the manifolds and raise them up on the bolts and retighten them.
-Fred-
Great history in these pictures!! Very well captioned.
-Fred-
The new owner is the one that added that tach.
-Fred-
I know this car quite well. My friend bought it over 20 years ago just because he liked 65 Cyclones as he had a fond memory of some interaction with a female in one when he was younger. The car was just in average condition with no rust. It had water running out of one of the tail pipes from a blown head gasket. When I first saw the car I thought somebody had swapped a drivetrain out of a K Mustang. He had the car for about a year and when I was working on it I found the build sheet behind the drivers door panel. Up to that point we had no idea that this car was the real deal. I added the Mustang disc brakes to it about 3 years ago. The current owner bought it from my friend about 6 months ago.
-Fred-
Relisted on Ebay again with the same $67,000 price and also for make offer.
http://cgi.ebay.com.au/ws/eBayISAPI.d…hlink:middle:au
-Fred-