Judging purely by the instrument bezel and glove box door, this Kar likely was not a factory GT. This Kar warrents further inspection regarding its "factory" installed GT status.
-Fred-
Judging purely by the instrument bezel and glove box door, this Kar likely was not a factory GT. This Kar warrents further inspection regarding its "factory" installed GT status.
-Fred-
Dave, as funny as it may appear that actually is an accepted way to adjust solid lifters. It can be very messy, and I wouldn't do it any more but back in the day when these Kars were new, that was one of the ways. Tool companies came up with clips that went over the rocker on the pushrod end for Chevys and Fords to keep the oil from squirting on the fender aprons and headers. Here is a link to the Jegs catalog for these clips.
http://www.jegs.com/i/Mr.+Gasket/720/1015/10002/-1
-Fred-
Are you looking for 63 and 64 style or are you looking for the 65 style?
-Fred-
Z.Ray, That Motorsport impeller has been gone for about a year now. The main Motorsport dealer that carried them had around 400 of them and sold them all to one customer. Motorsport no longer services that impeller.
-Fred-
Here is a partial set like the ones above and these sold for $750 on May 3, 2009 on Ebay. Maybe Gene can post the picture.
http://cgi.ebay.com/ebaymotors/ws/…%3AIT&viewitem=
-Fred-
Duke, Ralph is sending you down the right path on this. Here is another food for thought on your problem and I believe that this fits your scenario perfectly. If you are using stock springs with a high lift cam, you might be experiencing coil bind on the springs. This will be more of a problem at high RPMs which is where you are having your problem. You can check this also with the heads on the car by having your valve at its most open point. At that point you need to be able to compress another .100" more before coil bind or your setup will continue to give you problems. If the springs do coil bind then change the springs as Ralph suggests. Be aware of proper seat pressures for the new springs so have them checked to see what height you will need to set the springs at when installing them. The height is adjusted with the spring shims. You might also check to see if you have spring shims already as if there are and they are too thick, that will cause coil bind. Just a side note here, I have been running a 427 bowtie for 40 years with a ZL1 .600" lift cam. I have stock 3/8" pushrods and stock rockers arms. I have had the engine to 8,300 RPM many times and have never had a rocker arm or push rod failure.
-Fred-
Tom, That is interesting information which would tend to make the clamps without the tang correct for most of our cars. The factory would, of course, used up their existing stock with tangs first which would have an indeterminate time frame. Charles is correct that the NOS Ford clamps for the 22 series battery do have the tangs.
-Fred-
Brock, Please note my previous post about match balancing a standard flywheel to your original. That would apply to any replacement flywheel if you wish to retain your balance characteristics. That way you can use any flywheel that you wish. If you were building a fresh engine, balancing would be a normal procedure.
-Fred-
Congratulations David, That looks like an awesome find on your part.
-Fred-
Looking really good, Charles!!
-Fred-
The balancing characteristics between the two are different. If you look at a Hipo flywheel you will see a lot more balancing drill holes than on a standard flywheel. The standard flywheel will be fine if you match balance it to your old flywheel.
-Fred-
10 X 1 3/4" is the correct size. The 9" brakes are for a 6 cylinder car.
-Fred-
Rick, I do not have their catalog in hand but I looked it up on their website. Their number SU551 is not the correct one. If they have a shorter threaded one, that would be what you need.
-Fred-
Bob, I just replied to your PM.
-Fred-
This Kar is back on Ebay again. For what it is worth here is a new quote from the sellers description:
"If you haven't noticed, collector cars are starting to move back up in price. Demand has picked up in the USA and from international buyers. If you wait, you lose, the low price market is almost gone. Act now or you will miss your opportunity to get back in the collector car market at a good price. RARE !!! RARE!!!! FAIRLY PRICED !!"
http://cgi.ebay.com/ebaymotors/ws/…%3AIT&viewitem=
-Fred-
Robert, Your 64 1/2 is too early for the Arvinode system. No 64 1/2 Kars use the Arvinode system as it was not used until 10/16/64 which was well past the 64 1/2 production. It would still be a really cool system on your Kar but your Kar uses the transverse muffler system.
-Fred-
There is nothing in the book that indicates a munufacturer on the camshafts. Any parts that are Ford manufactured have Ford part numbers. Everything else is Cobra car or Shelby part numbers. I would think that Larry at Valley Head Service would most likely know. You could call him and let him know that I referred you.
-Fred-
Steve, The following is right out of the Shelby American Performance Equipment book under engine specifications for the valve system:
289 Cobra High-Rev Racing Engine
Camshaft type: Roller tappet
(All specifications taken at 0.001" valve lift for all three camshafts listed below)
Valve lift: 0.485"
Intake valve opens: 40 degrees BTDC
Intake valve closes: 78 degrees ABDC
Intake valve duration: 298 degrees
Exhaust valve opens: 84 degrees BBDC
Exhaust valve closes: 25 degrees ATDC
Exhaust valve duration: 289 degrees
Intake tappet clearance (hot) .012"
Exhaust tappet clearance (hot) .014"
289 Cobra Racing Engine # S1CR-6003-4
Camshaft type: Flat tappet
Valve lift: 0.500"
Intake valve opens: 37 degrees BTDC
Intake valve closes: 72 degrees ABDC
Intake valve duration: 289 degrees
Exhaust valve opens: 76 degrees BBDC
Exhaust valve closes: 33 degrees ATDC
Exhaust valve duration: 289 degrees
Intake tappet clearance (hot): .025"
Exhaust tappet clearance (hot): .025"
289 Cobra Road Racing Engine # S1CR-6003-3
Camshaft type: Flat tappet
Valve lift: 0.445"
Intake valve opens: 29 degrees BTDC
Intake valve closes: 75 degrees ABDC
Intake valve duration: 284 degrees
Exhaust valve opens: 75 degrees BBDC
Exhaust valve closes: 29 degrees ATDC
Exhaust valve duration: 284 degrees
Intake tappet clearance (hot): .018"
Exhaust tappet clearance (hot): .018"
-Fred-