I have sent you both an email and a PM.
-Fred-
I have sent you both an email and a PM.
-Fred-
Just a few items that really stick out:
Fog light switch too far up on the dash panel
C8ZE replacement harmonic balancer
Why do people put the coil on the drivers side?
Inline fuel filter before fuel pump
No button top CARbureTER casting fuel pump
What is that cylindrical piece in front of the master cylinder?
Odd heater hose strap
Starter solenoid upside down
Odd PCV hose
Poorly done fuel line to carb
Replacement rear springs
Too many more for the time that I have available.
This one would have needed a lot of your help Troy and that would still have not made it a factory GT.
-Fred-
Jack, the seller states that this information is in the K code registry. Therefore he is basing this statement on only what is known to us to exist or has been reported to the registry. The seller is basing this on 64 1/2 only Kars. However the seller does state that this is one of less that 100 built and should state only that this is one of less than 100 known examples.
-Fred-
Quentin, I have seen quite a few of these pumps as everone on this forum probably already knows. If he looks closer at the 39S number he will probably find an 11 between the 39 and the S. I have seen several of them with the 11 sqeezed in and they are not always easy to make out. If it is a 3911-S, which it probably is, then it is a standard 289 pump which is correct for his car.
-Fred-
Brant, I concur with Ralph on the hose for a Hipo being the same regardless of production date. The 1965 only bound Ford parts catalog lists a C5ZZ 2282 D for this application as does the later loose leaf Ford parts catalog. I agree that the location where the hose mounts to the body would not matter to the part number as much as to where it mounts to the rear end housing.
-Fred-
Back on Ebay again with a lower starting bid of $15,000 and a lower Buy-It-Now of $25,000.
http://cgi.ebay.com/ebaymotors/ws/…K%3AMEWAX%3AVRI
-Fred-
This Kar only had one bidder and it sold for $18,500.00 on August 18, 2009.
-Fred-
Very Cool!!!
-Fred-
Mark, this is purely an opinion but I believe that in this case it will make sense. Ralph has stated it very well in his post which he made while I was writing this post. This low profile Rally Pac was not used until the GT and pony interior option was available which was on the first anniversary of the Mustang production on April 17, 1965. These cars were obviously produced slightly before that but no Rally Pacs for these would have been in the publics hands before this date. Therefore, to me, an early low profile Rally Pac car would be from April 17, 1965 to sometime prior to the end of 1965 production. This would place your Kar into the early production.
-Fred-
I just sent you an email on this.
-Fred-
Brock, you are correct on this. I looked at all of the related posts on this Kar and the previous owner did not mention the probability that this is not a Hipo short block. All that has ever been mentioned is that the C5AE 6015 E cast block has been rebuilt. This would lead some people to believe that it is a Hipo short block. There are a lot of pictures of things that are unimportant to the authenticity of the Kar but none of importnant issues like the rear end, undercarriage and VIN stamp on the block. I should have looked at this Kar when the previous owner was much closer to me. Perhaps someone closer to the Kar should inspect it.
-Fred-
Mark, that is very informative. We can always learn something new on this site with the wealth of knowledge that our members share.
-Fred-
Jack, your Kar has a standard interior and therefore uses a high profile Rally Pac. The pictures of your Kar show a high profile Rally Pac which will have the 6 on it. All of the high profile Rally Pacs have the 6. The low profile Rally Pacs are meant for cars with the 5 dial instrumentation which in 1965 was only on GT or pony interior cars. All 1966 Mustangs had the 5 dial instrument cluster and were intended to have the low profile Rally Pac as an option. I have a few low profile Rally Pacs and all of them do not have the 6 as the clock setting stem goes right through where the 6 would be. They do have the 18 above the stem.
-Fred-
I had to buy fuel pump cores to get the springs.
-Fred-
Gerald, I am glad that you are pleased with the results. Thanks for the plug.
-Fred-
Very good looking Kar.
-Fred-
Jack, these plates do not wear out however they can be severely rusted. The main reason for need one of these plates is if the car was rebodied and the person doing the rebody failed to transfer the plate. The problem with all of this is that the plate is one of the ways to verify the authenticity of a K code car. Future purchasers of K codes will need to really inspect this plate closer to make sure that it has a factory look to the spot welds to make sure that they are not purchasing a rebodied Kar. This plate was also used on non K GT cars in the 66 model year as Charles Turner has already pointed out.
-Fred-
Back on Ebay again with a slightly lower Buy-It-Now of $36,695:
http://cgi.ebay.com/ebaymotors/ws/…K%3AMEWAX%3AVRI
-Fred-
Back on Ebay again with a higher starting bid of $18,500 and a lower Buy-It-Now of $26,500.
http://cgi.ebay.com/ebaymotors/ws/…K%3AMEWAX%3AVRI
-Fred-