I have quite a few of the NOS lower 65 adjusting rods. They do vary slightly in length and finish from each other.
-Fred-
I have quite a few of the NOS lower 65 adjusting rods. They do vary slightly in length and finish from each other.
-Fred-
The 65/66 Shelby rear wheel cylinders are a C3OZ 2261 A for the right hand side and C3OZ 2262 A for the left hand side. They are indeed a 15/16" diameter bore.
-Fred-
Back on Ebay again with a Buy-It-Now of $24,500 or best offer:
http://cgi.ebay.com/ebaymotors/ws/…K%3AMEWAX%3AVRI
-Fred-
Joel, There are no available production numbers for any 65 or 66 K regardless of body style. One thing for sure is that all 65 K fastbacks were 4 speeds.
-Fred-
The frame will have a casting number on it that starts with 65 for a coupe and 76 for a convertible.
-Fred-
The front drums are the same as standard 8 cylinder Mustangs.
-Fred-
My guess on the heater hoses is that they are disconnected due to a heater core leak. You can see where the heater hose connections on the engine are coupled together with a piece of hose thereby bypassing the heater core. The blue engine may be just because he seems to like blue. There seems to be a lot of other blue items on the engine.
-Fred-
The pony interior is unlikely to be correct as the serial number places the car in late Feruary 1965. It is also missing the door lights.
-Fred-
Brian, The picture of the Henry Ford II car appears to have a drum brake master cylinder as it has a screw on cap rather than the clip on of the disc brake cylinder. Am I missing something here? The brake pedal does not say disc brake on it either. I did not notice disc brakes as being listed in the article. Maybe that car does not have disc brakes?
-Fred-
Rick, I left the welded brackets on the shock towers for the shock tower braces intact. That way I could always put everything back as original. It will be necessary to improvise new steel brake lines to the master cylinder as it will be further forward. This way you can save your originals for future use. I used a regular Mustang disc brake master cylinder as early versions do not have the push rod attached and work well with the brake booster.
-Fred-
Rick, I have done this swap before and it is successful. Yes, the master cylinder interferes with the left side shock tower brace. I used an export brace to fix that problem as it sits higher and helps to clear the master cylinder. The master cylinder still hits lightly on the brace and you need to give a gentle pry on the cylinder to remove the cap. I did this swap as I was using 10 X 2 1/2" rear shoes with metallic linings and metallic linings for the disc pads. The car had a C6 trans and a Hipo engine and when my wife would back it out of the downward sloped driveway, she had trouble stopping it in the mornings. The booster did help some but being as it was so small compared to some other booster, it was not as effective as I would have liked. Keep in mind that the Mustang booster setup lowers the brake pedal and decreases the brake pedal travel. The linkage multiplies the travel to the master cylinder thereby making it work normally.
-Fred-
Mark, Replacing the fuzz would be like glueing the feathers back on a chicken.
Do not waste your time. If you need NOS belt line weatherstrips, just contact me as I have some available.
-Fred-
I emailed the seller and the Kar has been sold.
-Fred-
As an added note to Daves post, while you have the door panel removed, also remove the large lower window stop rubber block. That will get the window down and out of your way.
-Fred-
The actual Ford part number is a C1UW 1177 A and the original that you have actually has the part number on it which is unusual. The C1UW number is usually an engineering number and the part number would have been a C1UZ. This is a rare exception to the rule. I have NOS ones in the Ford box where one has the Ford C1UW number and others have a National seal number of 51322.
-Fred-
The stampings on the engine actually do match the trans in both the type style of the three and the oversize K.
-Fred-
The engine stamping certainly does add credibility to this subject. This is especially true due to the fact that your father has owned it since it was new. It must have been a tough day at the assembly plant when your Kar was built!!! Maybe this is a Monday Kar after a party weekend.
-Fred-