It is correct that a 65 did not come with an automatic. The seller does state in the description that the factory 4 speed was converted to an automatic.
-Fred-
It is correct that a 65 did not come with an automatic. The seller does state in the description that the factory 4 speed was converted to an automatic.
-Fred-
Good eye, Craig. I guess that is why I could not find the choke cable. The air cleaner is a low priced repro as well.
-Fred-
Is this for disc or drum?
-Fred-
This Kar actually has an 8" rather than a 9" rear end. It also has the smaller standard alternator pulley.
-Fred-
Mark, The men in the white coats don't bother me. It would only worry me if I woke up to a rescue person looking over me. ![]()
In regards to Dons Arvinode system, I did drive his Kar today and it was great. The noise level does not seem much louder than my 66 factory Hipo muffler and resonator assemblies. His system does start rapping some at higher RPMs but that is just cool!! I am surprised that the people that owned these Kars when new would have complained about the noise enough to cause Ford to replace their mufflers at that time. What a bunch of wusses!! The muffler system on a Barracuda "S" model was noisier in my opinon.
-Fred-
I commend the seller for running an honest auction with all of his disclosures.
-Fred-
am unclear as to what you are actually looking for however Ford did service the third member assembly and called it the differential assembly-rear axle in the parts book. The 3.50 non locking assembly has a number of C4ZW 4200 C. It would only have been available as an assembly line piece when ordering as a service part and then only from current production. You are just a tad bit late to order one. The ring and pinion gear set was a B7AZ 4209 D. This was replaced by B7AZ 4209 G and then by B7AZ 4209 L which was then replaced by C9OZ 4209 A and lastly an E3UZ 4209 A. When these were last available from Ford they were a little over $500. If you need an NOS Ford ring and pinion, I do have one in stock.
-Fred-
Don forgot to mention that this is not just any reproduction exhaust but rather the Arvinode system made by Waldrons with Dave Wallace providing the impetus to make it all come together. Bring your old rag top by the LZ on Saturday and I will test it out for you at no charge.
I'll even give you a free ride up the hill to celebrate your accomplishment.
-Fred-
The VIN that you figured for this Kar appears to be correct.
This is the first time that I have seen an export buck tag with an actual destination country. That is pretty cool.
-Fred-
Rene, I just sent you a PM on this.
-Fred-
Of note on this Kar is the crack in the door where the door latch screws on by the data plate. The apron where the buck tag screws down looks pretty rough also like it may have some scaly rust although it is possible that the engine compartment was just not prepped well before it was painted. The 4 way flasher switch is not properly mounted in the glove box but rather to the right of the steering column under the dash.
-Fred-
For comparison purposes, the Mecum Kar listed above does not have a pony interior or a console. It would be important to note whether the Kar you are trying to sell is a 76A, 76B or 76C body style originally.
-Fred-
Does this Kar have a pony interior?
-Fred-
According to my older Ford parts master catalog, those shocks have an actual Ford part number of C5ZZ 18124 B. Their application is for 65 and 66 Mustang with 6 or 8 cylinder except 289 Special.
-Fred-
Lyle, the cylinders were for a 63 to 65 Fairlane station wagon.
-Fred-
To comtinue with Ralphs response, the tab is always there on any OEM original or any replacement spring perch.
-Fred-
This Kar sold for $21,000 on September 25, 2009 on Ebay.
-Fred-
Our Hipo engines were produced at the Cleveland plant.
-Fred-
Rick, this rod only fits some 65 Mustangs, Falcons and Fairlanes. It does not have any other applications.
-Fred-