I need the following for my car:
- NOS upper ball joints
- NOS upper/lower Ball joint Boots (C4 part number)
- NOS Strut rod bushing kit (LH/RH)
Wayne
Posts by wcampbell_old
-
-
My '65 is missing one the the black "rain guards" that bolts to vents 2 and 4 in the fastback air extractor assembly. I need the larger of the two for the left hand side in my car. I also need both large wire clamps that are used to hold the air extractor drain hoses on to the extractor assemblies. Does anyone have any extra of the items laying around they would be willing to sell? Any help would greatly be appreciated.
Wayne
-
-
I have a std bore '66 HIPO Block dated 5M1 (December 1, 1965). No VIN stamping on it. Asking $1300 or trade for S1MS COBRA T Pan.
-
Steve,
I'll be there Friday and Saturday. If you can bring the springs I'd like to take a look at what you have. I'll call your number below and try to catch up with you.
Wayne
<BLOCKQUOTE id=quote><font size=1 face="Verdana" id=quote>quote:<hr height=1 noshade id=quote>
Wayne-
Its steve, I have a set of orig leafs--not sure on part number, I have them at saac with me?
Are you coming?
steve 301-502-1337
<hr height=1 noshade id=quote></BLOCKQUOTE id=quote></font id=quote><font face="Verdana" size=2 id=quote>
-
Hello all,
I'm in need of the leaf spring bottoms to put underneath my kar. The part number I need is C4ZA-5556-S. Any dates from January - April '65 will work. Please contact m if you have a set you are willing to part with.
Wayne
-
Just for reference I looked at the yoke. The part number casting is poor and hard to read but what I found legible was "22083-3N"...
-
In need of a nice '66 C4 Slip yoke designed for the inside clip style U joint retainers. My Jan '66 289/Auto yoke has a groove in it and I want to put something better back since I'm putting in fresh U Joints. Let me know if you have one you're willing to part with.
Wayne
-
Hertz Sports Car Club memorabilia on ebay:
Coaster:
http://cgi.ebay.com/ebaymotors/196…=item2a0d0d562f
Jacket:
http://cgi.ebay.com/ebaymotors/196…=item2a0d0d63f3
Edited by - wcampbell on 01/06/2011 07:33:17
Edited by - wcampbell on 01/09/2011 07:23:37
-
I need two door latch springs for my '65. ANy one have a set willing to sell?
Wayne
-
Have an original C5OE HIPO damper I'd like to pass on to someone needing one. It's dated 4L; I'm asking $550 for it.
Wayne
-
I don't need the plate that bolts on the third member, but rather the little rubber "pyramid" that bolts to it - mine is torn. Any leads would be appreciated.
Wayne
-
-
Sent you a PM on the balancer.
-
I have the 5M1 dated HIPO block. If you're interested I'll work with you to get it to a good home.
Wayne
-
If any one is interested I'm potentially willing to separate the caps as I could use the 5M1 dated block for another non HIPO project.
-
Guys,
I receieved the block from an old skool shelby collector who swore the block was an original 289 HIPO block. It is a bare block with original HIPO mains from what I see. It measures 4 inches at the top of the bores. There is no VIN stamped on it. I don't know what else I can say.
Wayne
-
I have a std bore HIPO block. Casting on the block is 5M1. Block is located in Northern Virginia and is pickup only. Looking to have $1800 for the block.
Wayne
-
No. just a bare block.
-