If anybody would like pics of these pieces they can email me at s.sc@knology.net and I will gladly send them to you. I bought a hipo carb years ago and had exact duplicates made of the pieces. The only piece that doesn't match some carbs is the choke rod as I have seen 2 different styles. I only sell the style with the clip in the middle instead of the swedge type. This is because my original came with this style. Also the plastic piece and choke plate lever are different on a hipo carb. I include these pieces but it is not necessary to change them out if you use the plastic piece from your automatic choke. Steve
Posts by 2fst4u_old
-
-
I have reproduced an exact copy of the hipo manual choke pieces for the 4100. Anyone interested can contact me at s.sc@knology.net. Price is $65 I also reproduced the over the counter racing part vacuum override piece for the 4100 to turn the carb into a manual secondary. $20 for this item
-
I have a NOS roll of emberglo material and a roll of NOS parchment. Enough to do the seats of a 65 66 mustang. $100 plus shipping
email me at s.sc@knology.net if interested as I do not check posts very often
-
Yes That's it. I found a hipo carb years ago with it installed and thought it would be a good item to reproduce
-
I have a 71 dated small block x manifold for sale. This was from the last of Fords racing program. This intake goes with the special windsor/cleveland style heads that Ford produced in 71 and put on Mavericks and Comets. Windsor style intake, cleveland valves and chambers and 2 barrel cleveland exhaust ports. I may have a set of heads available also if interested. $150 email me at s.sc@knology.net as I don't watch this site very often.
-
I have reproduced the vacuum secondary override linkage that was available over the counter thru the Ford racing program. Slips on carb in a few minutes and turns it into a manual secondary carb. $20 includes shipping email me at s.sc@knology.net as I do not watch this site very often
-
<hr class="bbcode_rule" />
I didn't put in instructions as there are only a couple of screws to remove and put the choke pieces in the same place. As for the rod it is an exact copy of the one from my hipo carb. There may have been a couple of suppliers as there were for many parts. I have seen a rod that uses a clip like the one I sell and a rod where the stop area is sort of squished out for support. The holes that need to be filled are the vacuum holes that go to the automatic choke. Last when it comes to the flap lever this can be the most difficult.It is a soft brass that is peened over that holds on the lever. All I did was carefully wiggle the existing off and set the new lever in place. I then used a small ball peen hammer and tapped the bent brass back over. I hope this answres all your concerns. Also I have heard of pony carbs, went to there website and they do not sell the pieces seperately. -
I wasn't aware they were making these. Mine are US made, copied exactly from a Hipo carb. My kit also includes all the pieces including the choke flap lever which is different and exact copies of the plastic pieces that fit into which are different from standard 4100's
-
I have reproduced all the manual choke pieces for the 4100. If you are missing your pieces or want to convert to a manual choke this kit is for you. $89 plus shipping. respond to s.sc@knology.net
-
I have a NOS roll of 7 yds of emberglo and 4 yds of parchment vinyl that I bought years ago . There is enough material here to do an interior. $600 I can be reached at s.sc@knology.net
-
I have a 3.50 open center section available Date code 6b24 $125 shipping from 33759
-
I have reproduced the override linkage for the 4100 carb that was available from Ford in the 60's. This converts the 4 barrel into a manual secondary carb. $19.95 plus $5 shipping. contact s.sc@knology.net
-
I have a limited quantity of the reproduction silhouette light. Available in either clear or amber lens. $65 plus $7 shipping. Contact s.sc@knology.net
-
I have an NOS headlight bucket that I have been holding for about 15 years. I am selling off all my extra parts. This is for the drivers side. Pic available upon request. contact s.sc@knology.net
-
I have an NOS headlight bucket that I have been holding for about 15 years. I am selling off all my extra parts. This is for the drivers side. Pic available upon request. contact s.sc@knology.net
-
i have a conversion kit available for you. I will be selling these shortly to the public. If interested email me at s.sc@knology.net
-
I picked up a box of NOS 289 hatchets at the Ford Carlisle show. Will be selling them for $40 each plus shipping of $5. You can contact me at s.sc@knology.net. I have pics if you would like, not sure how to load them on this site.