Posts by paul_old

Three NOS C5ZZ-5C299-A MLDG W/ATTG PARTS in Ford boxes. $150 for pair, $200 for all three. Paul @ 817-691-0159 or deemarvin@tx.rr.com .

Jeff, I sent you a pm but have not recieved a reply. Please contact me @ deemarvin@tx.rr.com . Thank you, Paul.

Dan, I have been looking forwards to hanging out with you and all the rest of the Tyler gang since about this time last year. As for car parts, I am not planning on bringing any unless someone asks specifically for me to bring something up there. I will be with Rick and the guys from Little Rock too. Tulsa is the highlight of the summer for me and has been for years. I hope it will continue for many years to come.

Can deliver to Tulsa, OK this june. Paul.

I still have a few of the items listed above plus many other hipo 289 and original 65/66 GT 350 stuff. I can bring to Tulsa for the Mid America Shelby meet this june 24-28. Paul

MSuHsEtLaBnYG, I do have an oil pan and Richard, I do still have the 1.08 carb. Paul @ 817-691-0159 or deemarvin@tx.rr.com .

The 6M heads have been ported and polished. Bigger valves. The push rod slots were worn so giude plates were intalled. The cresent shaped steam passages in the bottom of the heads have been welded up too. All the above were done before I owned the heads. Paul.

Also, I forgot to list on initial posting the following:

NOS upper and lower FORD 65 mustang control arms @ $1000/ALL FOUR

NOS L $ R door hinge asy. C5ZZ-6522810-B & 6522811-B @ $200/PR

NOS L & R door wx strip C5ZZ-6520531-A & 6520530-A @ $250/PR

eight NOS Boss 302 rods in Ford boxes $800/set

used hipo 289/ boss 302 rods, floated $400/set

cast iron 4V intakes $100 ea.

C8 part #'d hipo balancers $250 ea.

motorcraft dual point distr. $250

hipo timing gear hatchets $100 ea.

1.08 4V Autolite 4100 non hipo carb dated 66, $70

driver's side hipo exhaust manifold $100

hipo std bore short block dated 5B(crank, rods and pistons installed) never disassembled $3500

hipo 289 heads, one dated 4C other 4D, machined and assembled $1200

hipo 289 heads dated 6M, thermactor, modified, machined and assembled $1200

Lots of Shelby stuff too. Paul

There are alot of us who need the intermediate triangular left and right hand pieces for the motor mount. If you produce them you would have alot of folks, me included, wanting to purchase them from you. I hope you do take on the project. I just bought the long stud(carriage bolt) from AMK. Paul.

Are the heads C5 castings or are they C4 castings? Thank you, Paul

Please call to discuss. Paul @ 817-691-0159

Please call to discuss. Paul @ 817-691-0159.

Please call or email to dicuss parts I need for my project as well as parts I have that you need for your project. Thank you, Paul @ 817-691-0159.

-Standard bore never disassembled hipo block, hipo crank, hipo timing gear assembly with hatchet, hipo rods and pistons. Block dated 5B13

-Unmolested hipo 289 heads dated 4G23/16

-Hipo 289 flywheel

-C3 hipo harmonic balancer

-Timing gear cover

-FoMoCo dual point distributor dated 5KA

-Cast iron 4V intake

-Used steel oil pan

-used chrome valve covers

$7500 Paul @ deemarvin@tx.rr.com

For sale: L & R non GT doors. Stripped, patched(2" X 2" at bottom front corner), and in primer. No internal components or glass. Excellent condition, $1000/pr plus shipping. Paul

I will be going to Tulsa for the Mid America Shelby meet in June. If anyone in need of 66 GT 350 parts is also planning on going, please contact me ahead of time so I can be sure to bring the items needed with me. The following is a partial list of ORIGINAL 1966 SHELBY parts I have collected:

4100 Autolite carb, two S2MS Cobra intakes, open letter cobra valve covers, closed letter cobra valve covers, sway bar, export brace, monte carlo bar, aluminum T-10 4 speed, 11-65 dated koni rear shocks, Impact brand chrome lap belts, 14" chrome Magnum 500's, plus alot of hipo 289 stuff. Paul @ 817-691-0159

-1966 dated Impact chrome lap belts $700

-Export brace $350 SOLD

-Monte Carlo bar $150 SOLD

-Front sway bar $250 SOLD

-Brake cooling scoops $350

-Plexiglass 1/4 windows $350

-Large Cobra S2MS intake $750

-S1MS Cobra T-oil pan $1000 SOLD

-6 Chrome 14" Magnum 500's(rough) $1000

-Restored 4100 hipo carb $1500 SOLD

-NOS 6C air cleaner base(no tube)$150

-Cobra valve covers $250

-Buddy Bar open letter Cobra valve covers $500/$800 restored

Paul @ 817-691-0159, or deemarvin@tx.rr.com

I have all the above for your 65. Thank you, Paul @ 817-691-0159.

I received the hipo air cleaner top and base in the mail today. The base is stamped 6C and does not have a tube for the closed emissions. The top is an original that has been rechromed, it is beautiful. Paul @ 817-691-0159

I received the hipo carb in the mail today. It came to me directly from Pony Carb (Las Cruces, New Mexico) who restored it for the previous owner. It is beautiful and has the following codes on it. Tag reads:

AUTOLITE

C6ZF F

A 624

base is stamped 6ZF

John at Pony quoted the carb at $1700.00. For sale for here for $1500.00. Paul