I have 2 block available. Block # C3AE-6015-N is dated 3E14 (5-14-63 with a build date of 3E28-H (5-23-63. It is freshly borded 20 over with new cam bearings. Block # C3OE-6015B is a short block assembly minus the balancer. Casting date of 3F11 (6-11-63) with a build date of 3F18-c (6-18-63)
Ken
I have 2 blocks available. Block # C3AE-6015-N is dated 3E14 (5-14-63 with a build date of 3E28-H (5-23-63. It is freshly borded 20 over with new cam bearings. Block # C3OE-6015B is a short block assembly minus the balancer. Casting date of 3F11 (6-11-63) with a build date of 3F18-c (6-18-63)
Ken
This is the info on your tranny HEH-G 1964 Mustang 260, 289 wide 25-spline.
Ken
I'm looking for a center carb for a small block tri-power set-up. The list number is R-2881 and the Ford number would be C4AF-9510V and if it still has it's tag it would be C4AF-U.
Any leads would be greatly appreciated Ken
I have the following intakes available. 4J15 9-15-1964 and 4K21 10-21-1964. Price is $150.00 plus shipping if you are interested.
Sincerely Ken
I have gone to adding GM's EOS (Engine Oil Supplement) to my crank case. It was recommended in one of the articles I read about this situation. I add one bottle to every oil change in my Shelby. I'll go back through and try to find the article and post it here. Recently I have been told that Shell's Rotella T, once ok to use, has now changed their formula also, making it unfavorable to use. Most oil companies have a webb site were they address concerns and make recomendations for our applications.
Ken
I have the standard hipo piston and should have a flywheel. Is there a specific date for the flywheel?
Ken
Caps are sold.
Ken
Hi Duncan, I sent you a private message with some pics of the caps.
Ken
I have a set of Hipo main caps that I've elected to sell on this site rather than E-bay. I acquired a 289 Hipo short block assembly that had been stored since the 60's by a racer. The block is not usable so I'm going to part it out. The caps are perfect with no issues, price is 1,000.00. I can provide pics apon request.
Ken
I purchased a Stainless steel box from Cosco's about a year ago and I love it. It has ball bearing drawers(A must)and is perfect for home use. Each drawer will hold about 250LBs of tools. My Craftsman boxes won't hold up and in fact failed from the weight of the tools. If you look at the Craftsman tool boxes you will see that they are made pretty cheaply. Go to Cosco's and check out there box. I'm planning on getting another one after the holidays.
Ken
Hi Marv,
Thanks for your imput, although this is a HiPo block, and I believe they did not put Hipo's in Tigers. Your thoughts?
Ken
Ok guys I have a interesting question for all the K-Code Guru's out there. I just aquired another HiPo long block with big caps additional crank weight hipo rods hipo crank etc. Now here is were it gets interesting. The casting number on the block is Z5AE-6015-A and was cast 4F26. That was not a typo it is Z5 not C5 and is a 6 bolt casting. I aquired this block from a 60's drag racer and he claimed he would get his blocks (Motors) from Mercury Marine. The block does not have a vin number which if purchased over the counter so to speak it would not. OK the big question is, has anyone ever heard or seen a block cast this way???
Ken
I have two HiPo's and a few standard 260's and 289's. What are you looking for casting and date etc?
Ken
I Have a correction in the part number. The number is C5DA-6394-A
Ken
The date can be located on the flat spot usually to the lower left of the hole for the transmission. There will be a circle with the year cast into the bellhousing. Along the outside of the circle will be one to 12 raised dots which represent the months of the year. One being January etc.
Ken
Hi Marv,
I will be there as always. This is one of the best Ford swap meets in the Country.
Ken Hartley
The 10/64 bellhousing has been sold.
Thanks For looking Ken
Well its time to clean off another shelf. I have the following bell-housings forsale at 75.00 each plus shipping. They will need to be cleaned up and all are aluminum C5DA-6394-B. I can bead blast your purchase for a small fee if you wish.
10/64
2/65 one bolt hole has a little section missing but will not show with a bolt in it.
3/65
5/66
6/66
7/66
2/67
Edited by - SixT5HiPo on 10/19/2006 22:42:17
I have two pair of the plates as you described. They are a little rough around the edges but I feel once welded in and the appropriate sealer placed around the edges they would like fine.
Ken Hartley
