Fuzzies and 289 emblems are sold.
Posts by SSBB396
-
-
Posting here before going to eBay
The content cannot be displayed because you do not have authorisation to view this content. to see if there is any interest. The content cannot be displayed because you do not have authorisation to view this content. The content cannot be displayed because you do not have authorisation to view this content. The content cannot be displayed because you do not have authorisation to view this content. The content cannot be displayed because you do not have authorisation to view this content. The content cannot be displayed because you do not have authorisation to view this content. The content cannot be displayed because you do not have authorisation to view this content. The content cannot be displayed because you do not have authorisation to view this content. The content cannot be displayed because you do not have authorisation to view this content. The content cannot be displayed because you do not have authorisation to view this content. The content cannot be displayed because you do not have authorisation to view this content. The content cannot be displayed because you do not have authorisation to view this content.
NOS Fastback Fuzzys complete set -- Offers over 200.00 consideredNOS Hipo badges older FOX type Offers over 100.00 considered
NOS 289 badges FOX type Offers over 75.00 considered
NOS GT badges older Offers over 100.00 considered -
Hello again! I already have my old account 66FBKGT linked to 66FBKGT_old but I can't remember the password. Can anyone help me reset it? The link is not working!
Maybe this new account can be linked to my old one? Should be the same email... -
Already rebuilt by damper doctor 4L date code. Not used after rebuild. Trade for a 5F-5H date code or make me an offer. I am not sure what these are worth.
http://cid-2ffe9000db6dc074.photos.live.com/self.aspx/Must…ts/DSCN2537.JPG
-
-
I have 6D22 intake and a 5G7 intake and I am looking for a 5H1 - 5J4 intake. Willing to trade or sell my intake(s) or purchase outright.
-
If all the blocks, heads, intakes, etc were cast at the same foundry, then they would have needed to be transported to the assembly plant to build the cars correct? In the case of the build date on the block --does that mean the day the engine was fully assembled?
I have a block that is one day apart from cast to build and another that is two days. Those dates seem way too close to be cast in one place then be transported to another and built. I have seen some that are a several days and heard of others that are weeks?
I wonder if the engines were assembled during the last phase of the build. Maybe that is why some were turned around so quick?
What about casting date of other parts of the engine (intake, heads) seems most originals are just a few to several days apart but I also heard of original engines with parts several weeks apart.
-
Looking for a complete set of hipo caps!
-
I just had to post this! Jeeps are one of my other passion aside from mustangs but this applies to both.
-
You may have an exposed wire or bad ground somewhere that is contacting the metal ring? I had to mess with my setup to get it to work good and consistently but it didn’t short on me
-
I have found this site to be valuable source of information over the years but I must agree lately it seems no one is updating anything. I have donated to the site over the years and I have been disappointed in the lack of response to some simple requests that I asked. I finally gave up also. Yes I do hope someone will take some ownership of this site and keep it updated.
-
NPD catalog page 140
For 289 HIPO
Specs: 10.4 x 1 1/16
Part #7561-3
-
http://cgi.ebay.com/ebaymotors/ws/…RK%3AMEWAX%3AIT
Do you think these heads were actually redone by Shelby? Do you think modifications like these reduce the value of the heads? Seller wanted 3K for them. What do you think heads are worth these days?
-
I recently saw a C stamping on GT A code car. All of the panels where stamped with C instead of an A and the door tag was the correct A code. The correct hangers, rearend bumper and frame rails were present. Human error was always a factor with early Mustangs since they were mainly built by hand with not a lot of automation.
-
No VIN stamped on the block
-
I thinking 7K OBO
-
http://cid-2ffe9000db6dc074.skydrive.live.com/redir.aspx?pag…000DB6DC074!195
Correct block and casting dated 6C25 (Standard bore)
Correct main caps, Boss 302 rods, C8 balancer and C8 water pump
Heads dated 6B25 6B31 Exhaust manifolds date 2/9/6 and 2/11/6
Intake dated 6B23
Distributor dated 6C29
Includes everything in pictures minus heater hoses.
Carb is a hipo clone
Fan is a repro
Rebuilt alternator is teardrop type but has correct pulley
fuel pump is correct button type but is not hipo and a little different than one pictured
Email me
Jason
-
I just got one of these. No instructions but overall nice pieces, The vertical choke rod is not exact and I'm not sure how you would replace the part that attaches to the choke flap shaft without special tools. I also wasn't able to order any HP choke parts from Pony Carbs without a core.
Oh yeah and the choke clamp bracket screws are a little to long
-
Is this feature working? Are these enabled on the site?
-
